ABB OmniCore V250XT Product Manual Download

Page: 391 / 456

LEDs for options 3G or WiFi

The illustration below shows the LEDs on the connected services gateway (3G or
WiFi).

xx1800000634

STATUS LED

LINK, 3G status or WiFi status LED

RF, signal strength status LEDs

Factory reset pin hole

Significance

Description

Startup sequence:

Red continuously: Default at power up.

Red, flashing: Power on self-test ongoing, operating system is
loading.

Green flashing: Loading application.

Green solid: Startup completed OK.

If the LED does not turn steady green after 30-60sec, it can be used to
identify the following issues:

STATUS LED
(red/green)

Fault indication:

•

No color: Power to the unit is missing.

•

Red, solid or flashing: Internal error. Replace the unit.

•

Green, flashing continuously: Communication error to another
module, view error messages.

For the connected services 3G, an orange LED indicator, externally visible
on the front, indicates the status of the 3G connection.

LINK

Orange:

•

ON, flashing: 3G modem on, searching network.

•

ON, solid: 3G modem on and connected to network.

For the connected services Wi-Fi, an orange LED indicator, externally
visible on the front, indicates the status of the Wi-Fi connection.

LINK

Orange:

•

ON, flashing: Wi-Fi transceiver on, searching network.

•

ON, solid: Wi-Fi transceiver on and connected to network.

Continues on next page

Product manual - OmniCore V250XT

391

3HAC073447-001 Revision: B

7 Troubleshooting

7.3.6 Troubleshooting the connected services gateway

Continued

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands