background image

Table 4:

Ethernet Configuration tabs

Tab

Description

Access points

This tab is used to configure access points.

The access point tab shows the access points

based on the supported hardware. For

example, if the 100FX-ST/100FX-LC hardware

modules are selected in hardware

configuration, the corresponding access points

will be available.

Merging unit

This tab is used to configure the merging unit.

Merging unit’s availability is based on the 9-2

order options and the hardware module

selection. For example, if OEM02 is selected,

the corresponding 9-12 merging units will be

available.

Routers

This tab is used to configure routers.

4.

Save the configuration data in one of the alternative ways.

Click the 

Save

 button on the toolbar.

On the 

File

 menu, select 

Save

.

Press CTRL+S.

5.5 

Using Graphical Display Editor

Graphical Display Editor is used for drawing the single-line diagram shown on the
graphical display of the IED. The diagram with its components corresponds to the
actual configuration.

1.

In 

Plant Structure

, select an IED.

2.

On the 

Tools

 menu, click 

Graphical Display Editor

.

The presentation is empty when no page exists for the IED. If standard
configurations are used, a default single-line diagram presentation is displayed.

3.

In the 

Symbol Library

 box, select either IEC or ANSI.

The symbols in the display pages and in the symbol library are changed.

4.

On the toolbar, activate the 

Snap to grid

 and 

Show grid

 functions.

5.

Create the single-line diagram.

5.5.1 

Creating single-line diagrams

1.

Add primary equipment to the display page by dragging from the 

Symbol

Library

.

Rotate the symbols with the Rotate left and Rotate right buttons on the
toolbar.

Select the size in the 

Symbol Size

 box.

2.

Add junction symbols for connections.

3.

Connect the symbols where necessary.

Section 5

1MRS757866 C

Use cases for engineering and commissioning

52

PCM600

Getting Started Guide

Summary of Contents for PCM600





































































Reviews: