background image

15

3 6 5 

Alarm indicators

The audio alarm has a series of beeps based 
on the active mode or a particular warning. 
See Table 8 below for the number/duration 
of beeps for warning/mode.

Table 8: Alarm function list

No 

Status

Alarm

1

Battery mode 

Beeps once every 

4 seconds.

2

Battery mode with 
battery low

Beeps once every second.

3

Bypass mode

Beeps once every 

2 minutes.

4

Overload

Beeps twice every 
second.

5

Warning active  
(See Warning & 
Fault Code Table)

Beeps once every second.

6

Fault active

Beeps continuously.

7

Button function active

Beeps once.

3 6 1 

Battery mode

To mute the audio alarm in battery mode, press 
the ON button continuously for 1 second. The 
audio alarm is active again when the battery 
reaches low status as a reminder that the UPS 
output power will shut down soon.

3 6 2 

Bypass mode

To mute the audio alarm in bypass mode, press the 
OFF button continuously for more than 1 second. 
This does not affect the warning and fault alarm.

3 6 3 

CVCF mode

The UPS can be used in CVCF mode without 
batteries. This will cause the Open Battery alarm 
to sound. To mute this alarm in CVCF mode, use 
the software.

3 6 4 

Other modes

To mute the audio alarm in any other mode, press 
the ON button for less than half (0.5) a second. 
You can enable the audio alarm again by pressing 
the ON button for less than half (0.5) a second 
again. If the new warning or fault alarm appears, 
the buzzer will beep again. 

— 

3 6 Alarm mute function 

3    G E T T I N G  S TA R T ED

Summary of Contents for PowerValue 11T G2 Series





























Reviews: