ABB Relion REG670 Technical Manual Download | Manualshive

Page: 638 / 1298

background image

The internal logic for each function block as well as, the input and outputs, and the
setting parameters with default setting and setting ranges is described in this
document. For application related information, please refer to the application manual.

14.1.7.2

Logic diagrams

Logic diagrams

The logic diagrams that follow illustrate the main principles of the SESRSYN
function components such as Synchrocheck, Synchronizing, Energizing check and
Voltage selection, and are intended to simplify the understanding of the function.

Synchrocheck

The voltage difference, frequency difference and phase angle difference values are
measured in the IED centrally and are available for the synchrocheck function for
evaluation. By setting the phases used for SESRSYN, with the settings

SelPhaseBus1

,

SelPhaseBus2

,

SelPhaseLine1

and

SelPhaseLine2

, a compensation is made

automatically for the voltage amplitude difference and the phase angle difference
caused if different setting values are selected for both sides of the breaker. If needed
an additional phase angle adjustment can be done for selected line voltage with the

PhaseShift

setting.

When the function is set to

OperationSC

=

On

, the measuring will start.

The function will compare the bus and line voltage values with the set values for

UHighBusSC

and

UHighLineSC

.

If both sides are higher than the set values, the measured values are compared with the
set values for acceptable frequency, phase angle and voltage difference:

FreqDiffA

,

FreqDiffM

,

PhaseDiffA

,

PhaseDiffM

and

UDiffSC

. If additional phase angle

adjustment is done with the

PhaseShift

setting, the adjustment factor is deducted from

the line voltage before the comparison of the phase angle values.

The frequency on both sides of the circuit breaker is also measured. The frequencies
must not deviate from the rated frequency more than +/-5Hz. The frequency
difference between the bus frequency and the line frequency is measured and may not
exceed the set value

FreqDiff

.

Two sets of settings for frequency difference and phase angle difference are available
and used for the manual closing and autoreclose functions respectively, as required.

The inputs BLOCK and BLKSC are available for total block of the complete
SESRSYN function and selective block of the Synchrocheck function respectively.
Input TSTSC will allow testing of the function where the fulfilled conditions are
connected to a separate test output.

The outputs MANSYOK and AUTOSYOK are activated when the actual measured
conditions match the set conditions for the respective output. The output signal can be
delayed independently for MANSYOK and AUTOSYOK conditions.

Section 14

1MRK502052-UEN B

Control

632

Technical manual

«
...
636
637
638
639
640
...
»

Summary of Contents for Relion REG670



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Relion REG670

Brand: Tripp Lite Pages: 20

Brand: DVIGear Pages: 4

Brand: CAYMON Pages: 4

Brand: Siemens Pages: 3

Brand: Siemens Pages: 3

7SG14 Duobias-M-200

Brand: Siemens Pages: 20

Brand: Siemens Pages: 29

Brand: Siemens Pages: 32

Brand: Siemens Pages: 48

Brand: Siemens Pages: 56

SIPROTEC 7XR8004

Brand: Siemens Pages: 70

Brand: Siemens Pages: 77

SIPROTEC 7SC805

Brand: Siemens Pages: 158

Brand: Siemens Pages: 160

SIPROTEC 7RW600

Brand: Siemens Pages: 168

SIPROTEC 4 7VE61

Brand: Siemens Pages: 330

Brand: Siemens Pages: 356

SIPROTEC 4 7SD80

Brand: Siemens Pages: 416

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands