N° Doc.
Doc. No.
Mod.
Rev.
M4379
SACE Emax
601933/003
Aparato
Apparatus
Escala
Scale
N° Pag.
Sh. No.
80/100
S PROTECTION:t=k/i
∧
z
I2: y.yIn
→
zzzzzA
t2: k.k s at 10 In
Thermal Memory: www
I PROTECTION: t=k
I3: x.x In
→
zzzzzA
t3: Instantaneous
de 1.5 a 2.0 con paso de 0.5
de 2.0 a 15.0 con paso de 1.0
y Off
from 1.5 to 2.0 with steps of 0.5
from 2.0 to 15.0 with steps of 1.0
and Off
G PROTECTION: xxxxxx
I4j: y.yyIn
→
zzzzzA
t4j: z.z s at In
G-S ZONE SEL.: www
Zone Selectivity
S ZONE Selec.:www
G PROTECTION: xxxxxx
I4j: y.yyIn
→
zzzzzA
t4j: z.z s at In
G-S ZONE SEL.: www
Zone Selectivity
S ZONE Selec.:www
<-PR112/LSIG PR112/LSI->
de 2.0 a 1.0 con paso de 0.02
y Off
from 0.2 to 1.0 with steps of 0.02
and Off
G PROTECTION: xxxxxx
I4j: y.yyIn
→
zzzzA
t4j: z.z s at In
G-S ZONE SEL.: www
Zone Selectivity
S ZONE Selec.:www
<-PR112/LSIG PR112/LSI->
<-PR112/LSIG PR112/LSI->
Confirm with the
↵
key which also allows you to pass on to the next
selection.
With the help of the
↑
and
↓
keys, select whether to enable (On) or disable
(Off) operation of the S protection with thermal memory. (This function is
only enabled with PROTECTION S: t=k/i
∧
2).
Confirm with the
↵
key which also allows you to pass on to the next
selection.
With the help of the
↑
and
↓
keys, select the threshold value I3 to be set.
The possible values are:
Confirmar con la tecla
↵
. Controlar el paso a la página sucesiva.
La página se encuentra disponible en dos versiones en función del tipo del
relé:
Seleccionar, con la ayuda de las teclas
↑
y
↓
, qué valor de umbral I3 se
tiene que programar. Los valores permitidos son::
Seleccionar, con la ayuda de las teclas
↑
y
↓
, si habilitar (On) o
deshabilitar (Off) el funcionamiento de la protección S con memoria
térmica. (Esta función sólo está habilitada con S PROTECTION: t=k/
i
∧
2).
Confirmar con la tecla
↵
que permite pasar a la página sucesiva:
Confirm with the
↵
key. Check that the next page is displayed.
The page is available in two versions according to the type of relay
selected
Seleccionar, con la ayuda de las teclas
↑
y
↓
, qué valor de umbral I4k o
I4 se tiene que programar. Los valores permitidos son:
Confirmar con la tecla
↵
y controlar que al lado de la selección del umbral
I4, se visualice automáticamente el valor del mismo expresado en
Amperios.
El cursor del display se encuentra listo para la selección sucesiva
With the help of the
↑
and
↓
keys, select the type of protection against earth
fault G, choosing between protection with definite time-delay (t4k=k) or
inverse short time-delay (t4=k/i
∧
2).
Confirm with the
↵
key which also allows you to pass on to the next
selection.
The page is available in two versions according to the type of relay
selected
With the help of the
↑
and
↓
keys, select the threshold value I4k or I4 to
be set. The possible values are:
Confirm with the
↵
key and check that the value in Amperes of the I4
threshold automatically appears beside selection of the I4 threshold.
The display cursor is ready for the next selection.
Seleccionar, con la ayuda de las teclas
↑
y
↓
, el tipo de protección contra
defecto a tierra G, eligiendo entre la protección a tiempo independiente
(t4k=k) o de tiempo corto inverso (t4=k/i
∧
2)
Confirmar con la tecla
↵
que también permite pasar a la selección
sucesiva
La página se encuentra disponible en dos versiones en función del tipo del
relé:
Confirmar con la tecla
↵
que también permite pasar a la selección
sucesiva.