1SDH002031A1002 ECN000092998 Rev. B
SACE Tmax XT2
– XT4 | 137
42 - Ekip Com DeviceNet
TM
Ekip Com DeviceNet
TM
is a communication accessory that enables Ekip Touch to be integrated
into a CAN network with communication protocol DeviceNet
TM
, with supervision and remote
control functions.
The module is configured as Slave and from remote it is possible to:
read Ekip Touch information and measurements
manage certain commands, including opening and closing actuator (MOE-E)
access information and parameters that are not available on the display
if connected to a withdrawable circuit-breaker, check the status of inserted / extracted
NOTE: the remote open and close commands to the switch can be run only if Ekip
Touch is in Remote configuration
To map the module in its communication network, the document System Interface is available
(page 128) that lists the necessary communication and command details.
To connect
Ekip Com DeviceNet
TM
to Ekip Touch, the
Ekip Cartridge
(page 129) and
Ekip Supply
(page 130) accessories are required.
Models
Ekip Touch can be configured with two different modules that are compatible with the
DeviceNet
TM
protocol:
Ekip Com DeviceNet
TM
and
Ekip Com DeviceNet
TM
Redundant
.
The two modules are identical in terms of characteristics and installation methods, except for:
display menus on unit, cablings and addresses for external communication, that are specific for
each model.
NOTE: if not specified, the information in the following chapter applies to both models
Both modules can be connected simultaneously to Ekip Touch to increase the potential of unit
(for example: for applications in which great network reliability is necessary).
IMPORTANT: in each Ekip Touch can be installed only one module per type; it is
not admitted the connection of two equal modules (for example: two Ekip Com
DeviceNet
TM
Redundant)
Connections
Consult:
the electrical diagrams for 1SDM000068R0001 to connect the module to its
communication network and for terminal references.
The connections must be made with Belden 3084A or equivalent cables.
the instruction sheets 1SDH002009A1503 to connect the module to
Ekip Supply
and
Ekip Touch.
Supply
Ekip Com DeviceNet
TM
is supplied directly by the
Ekip Supply
module to which it is connected.
In order to ensure correct operation, the DeviceNet
TM
bus must be supplied on the V+ and V-
terminals with a signal greater than 12 VDC.
NOTE:
the PLC ABB with DeviceNet (CM575-DN) communication module already
supplies the V+ V- supply
in the absence of the supplies from Ekip Supply and on the supply terminals of the
bus, the communication between Ekip Touch and module is interrupted.
Summary of Contents for SACE Tmax XT2
