ABB TRIO-20.0-TL-OUTD Installation Manual Download

Page: 5 / 7

TRACKSO WORKING

Insure correct connections as detailed in the installation guide.

Insert the SIM card.

Switch on the power to the TrackSo device. (Minimum 12V/1A input is required)

Power LED (Red) of TrackSo IoT gateway glows and stays ON.

NOTE:

TrackSo IoT Gateway will only be able to send data if the GPRS network is available at the

installed location.

LED

NAME

DESCRIPTION

GREEN

POWER

Light when Power on the device

RED

GSM

LED Status

Connection State

Flashing (ON for 100ms and OFF for 100ms)

SIM Card not found

Flashing (ON for 500ms and OFF for 500ms)

Searching for GSM Network

Flashing (ON for 0.1s and OFF for 2.9s)
Once at every 3sec

GSM Network Registered

Flashing twice at every 3sec

GPRS IP Connected

Flashing 5times

GPRS IP Sending data

LED OFF

GSM Fault

GREEN

COM TX

Blink on data transmission in RS485 port

YELLOW

COM RX

Blink on data reception in RS485 port

Summary of Contents for TRIO-20.0-TL-OUTD








Search results

Summary of Contents for TRIO-20.0-TL-OUTD

Reviews:

Related manuals for TRIO-20.0-TL-OUTD

Brands by name

Popular brands

ABB TRIO-20.0-TL-OUTD, Installation Manual

Search results

Summary of Contents for TRIO-20.0-TL-OUTD

Reviews:

Related manuals for TRIO-20.0-TL-OUTD

Brands by name

Popular brands