background image

Safety 

 

6 - EN 

TTH200 

CI/TTH200-EN 

 

 

1.5 

Plates and symbols 

 

 

1.5.1  Safety/warning symbols, note symbols 

 

 

 

 

DANGER – <Serious damage to health / risk to life> 

This symbol in conjunction with the signal word "Danger" indicates an imminent danger. 
Failure to observe this safety information will result in death or severe injury. 

 

DANGER – <Serious damage to health / risk to life> 

This symbol in conjunction with the signal word "Danger" indicates an imminent electrical 
hazard. Failure to observe this safety information will result in death or severe injury.  

 

 

WARNING – <Bodily injury> 

This symbol in conjunction with the signal word “Warning“ indicates a possibly dangerous 
situation. Failure to observe this safety information may result in death or severe injury. 

 

WARNING – <Bodily injury> 

This symbol in conjunction with the signal word "Warning" indicates a potential electrical 
hazard. Failure to observe this safety information may result in death or severe injury. 

 

 

CAUTION – <Minor injury> 

This symbol in conjunction with the signal word “Caution“ indicates a possibly dangerous 
situation. Failure to observe this safety information may result in minor or moderate injury. 
This may also be used for property damage warnings. 

 

 

ATTENTION – <Property damage>! 

The symbol indicates a potentially damaging situation.  

Failure to observe this safety information may result in damage to or destruction of the product 
and/or other system components. 

 

 

IMPORTANT (NOTICE) 

This symbol indicates operator tips, particularly useful information, or important information 
about the product or its further uses. It does not indicate a dangerous or damaging situation. 

 

Summary of Contents for TTH200

























Reviews: