background image

12 

Care Instructions / Warranty 

CARE OF YOUR ANTIQUE COPPER OR ANTIQUE BRONZE RANGE HOOD 

 
 

Pure copper or brass is used in the fabrication of your "Antiqued" ABBAKA Range hood. The 

optional utensil rail and "S" hooks are likewise made of pure brass. These exotic metals are then chemi-
cally aged to create a classic distressed look. A matte lacquer top coat is then applied to the antiqued 
metal's surface to "freeze the aging process". 
1.  DO NOT USE harsh alkali (i.e., oven cleaners) or acid base detergents (i.e., acid grout cleaner for 

tile), abrasive polishes, scouring powders or cleaning products containing ammonia, degreasers, 
strong chemicals or window cleaner products. 

2.  Use a non-fragranced, mild soap with a neutral pH, like Ivory Liquid detergent, in a 10 to 1 dilution 

with warm water. Use only soft cotton cloth (old baby diapers softened by many washings are excel-
lent). Soak the cloth in the diluted detergent and wipe in a straight blotting motion. DO NOT USE A 
CIRCULAR MOTION. DO NOT USE PAPER TOWELS as this wood-based product can scratch and 
damage the finish. 

3.  Dry the hood, again, using soft cotton cloth 
 

 

MAINTENANCE OF ENAMELED AND STAINLESS STEEL RANGE HOODS 

 
Hoods may be cleaned with any commercially available liquid cleaner. Avoid using cleansers with abra-
sives, as they may scratch the enamel or stainless steel. Brass utensil rails, if included, may be cleaned 
with a copper or brass polish (see previous page). Polished stainless steel rails may be cleaned with a 
soft cloth dampened with a mild soap and water solution, then buffed with a dry clean cloth to restore its 
luster. 
NOTE: Always clean and polish with the "grain" of the hood. The "grain" is the series of fine lines in the 
surface of natural polished metal hoods. It is usually horizontal. Do not clean in a circular motion. 
 

 

 

ABBAKA LUXURY RANGE HOODS 

Limited Three (3) Year Warranty 

 

 

 

ABBAKA warrants the products of its manufacturer to be free from defects in materials and 

workmanship for a period of three (3) years from date of acquisition by original consumer-owner. Mate-
rial which proves to be defective after inspection by ABBAKA, will be repaired or replaced at ABBAKA's 
option. No claims of labor, shipping costs or consequential damages will be accepted. This warranty 
shall not apply to product which has been altered, used for purposes and conditions other than those for 
which the product is intended; damaged as a result of shipping, misuse, negligence, accident, faulty in-
stallation or maintenance. 
 

The warranty covers the hood cabinet, hood liner and motors. 

 

The warranty does not cover: 
A. Freight damage 
B. Damage caused by faulty installation 
C. Service charges in your home 
D. Consequential damage 
E. Commercial or other misapplication 

Summary of Contents for Range Hood













Reviews: