c 2017 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: abhinfo@abhmfg.com
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
O
R
6000-2-14.DWG
REVISED 05-19-17
PAGE 2 OF 3
6000
13/16"
BEVEL EDGE DOOR
UNIVERSAL OR
SQUARE EDGE DOOR
BORE
5-3/8"
4-3/8"
6-5/8"
8-5/8"
5/32"
1-1/8"
CL
LOCK
&
STRIKE
BACKSET
13/16"
2-1/4"
7"
5"
2-3/4"
3-3/4"
BACKSET
DEPTH OF BORE
DOOR LATCH PROVISIONS
DEPTH
OF
BORE CHART
SEE DEPTH OF
1-1/8" DIA. (MIN)
DRILL FOR #8
WOOD SCREW
(2 PLACES)
1-3/4"
7/8"
2-1/4"
13/16"
13/16"
BACKSET
#8-32
TAPPED HOLE
(2 PLACES)
1-1/8"
1" DIA. HOLE REQUIRED, 2 PLACES
"HOLE" IN REINFORCEMENT
2-1/8" DIA.
HOLE THRU
5/32"
REINFORCEMENT BY
DOOR MFG.
7"
5"
2-3/4"
3-3/4"
BACKSET
UNIVERSAL OR
SQUARE EDGE DOOR
BEVEL EDGE DOOR
1" DIA. HOLE
(THRU ALL
SUPPORTS)
1-11/16"
3-3/8"
(4) 5/16" DIA.
HOLES BOTH SIDES
CL
LOCK
&
STRIKE
WOOD DOOR
METAL DOOR
EDGE GUARD NOTE:
WHEN PREPPING THE
DOOR FOR THE BACKSET,
DETERMINE IF THE DOOR
WILL RECEIVE AN EDGE
GUARD. IF SO, THE EDGE
GUARD SHOULD BE
INSTALLED FIRST AND
THEN THE PREP FOR THE
LATCH BACKSET SHOULD
BE MEASURED FROM THE
OUTSIDE EDGE OF THE
EDGE GUARD.
DOOR PREP INFORMATION:
1. BACKSET DIMENSION FROM LOW EDGE OF BEVEL.
2. CENTER PUNCH ALL HOLES.
3. DRILL HOLES (FOR HOLLOW METAL DOORS,
DO NOT DRILL THRU. CENTER PUNCH & DRILL
HOLES FROM BOTH SIDES OF DOOR).
4. REINFORCEMENT MUST BE APPLIED ON METAL
DOORS AT THE SCREW LOCATIONS.
5. REINFORCEMENT TO BE SUPPLIED BY DOOR
MANUFACTURER. THE HANDLE ASSYS MUST BE
SUPPORTED. THE LATCH BOLT UNIT MUST BE
SUPPORTED AND CENTERED WITHIN 1/16" OF
THE CENTERLINE AT THE BACK END.
ADA
RECOMMENDED
HEIGHT 44" FROM
FINISHED FLOOR
TO CENTER LINE
-OR-
CHECK LOCAL ORDINANCE
FOR PROPER HEIGHT
VERIFY BACKSET
CENTER LINE
6000 SERIES PUSH/PULL LATCH - DOOR PREP
1-3/4"
7/8"
2-1/8" DIA.
HOLE THRU
1-11/16"
3-3/8"
(4) 5/16" DIA.
THRU HOLES
USE PROVIDED
ORIGINAL FULL
SCALE
TEMPLATE TO PREP
THE DOOR
3-3/8"
1-11/16"
7/8"
1-3/4"
(4) 5/16" DIA.
THRU HOLES
HORIZONTAL MOUNTING
BACKSET
LOCK EDGE
OF DOOR
2-1/8" DIA.
THRU HOLE
(VERTICAL MOUNTING SHOWN
SEE BELOW FOR HORIZONTAL MOUNTING)
(VERTICAL MOUNTING SHOWN
SEE BELOW FOR HORIZONTAL MOUNTING)
