6600-C-AB SERIES, ASYLUM TRIM ROUND KNOB
INSTALLATION FOR MORTISE LOCK
c 2017 ABH Mfg., Inc.
printed in USA
O
R
www.abhmfg.com
E-mail: abhinfo@abhmfg.com
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
ISSUED 02-03-17
6600-C-AB-1-00.DWG
"C" ASYLUM TRIM ASSEMBLY
FACE PLATE
MORTISE LOCK
8-32 x 1/4" PIN-IN TORX
12-24 x 3/4" PH. F.H. COM. SCW.
10-32 x 1/2" FHMS
ADAPTER PLATE
8-32 x 1/4 PIN TORX FLAT HD. M.S.
8-32 x 3/16 PHIL. FLAT HD. M.S.
8
8
9
7
6
2
2
1
9
1
1
2B
2
5
6
7
3
4
8
8
ITEM
1A
QTY
1
PART DESCRIPTION
PATENT No. 6,196,599 & 5,730,478
1A
"C" ASYLUM TRIM ASSEMBLY
1
2A
1A
2A
2A
5
2B
2B
ASYLUM COVER
1
2C
SPINDLE
6600-C-AB
PAGE 1 OF 3
"C"
ASYLUM HANDLES
MUST BE MOUNTED
IN THIS POSITION
DOWN
LEVERS
ASYLUM TRIM ASSEMBLY
IS PRE ASSEMBLED
AT THE FACTORY
NOTES
1. TRIM MUST BE MOUNTED VERTICALLY.
2. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
3. USES AB6600 SERIES MORTISE LOCK DOOR PREP.
4. MORTISE LOCK CYLINDER & LOCK CAM NOT PROVIDED.
EDGE GUARD NOTE:
WHEN PREPPING THE DOOR,
DETERMINE IF THE DOOR WILL
RECEIVE AN EDGE GUARD. IF SO,
THE EDGE GUARD SHOULD BE
INSTALLED FIRST AND THEN THE
PREP FOR THE MORTISE LOCK
SHOULD BE MEASURED FROM THE
OUTSIDE EDGE OF THE EDGE
GUARD.
4
3
2C
INSTALLATION INSTRUCTIONS:
1. Prep for lockbody according to mortise lock manufacturer installation. Install mortise lock (item 6) using (2) 12-24 screws (item 8). Then
mount the face plate (item 7) using (2) 8-32 screws (item 9).
2. A) Place the pre-assembled asylum trim assembly 1A on the side of the door that will match the diagonal mortise lock mounting through
holes.
B) Place the adapter plate 2B centered with pre-assembled asylum trim assembly 1A while inserting the (2) 10-32 screws (item 5).
C) After tightening the mounting screws (item 5) test lock and asylum trim assembly 1A for proper latch retraction and knob operation. If
the latch does not extend / retract or if trim knob is binding, Loosen 10-32 head screws (item 5) and adjust alignment for proper
operation and re-tighten.
D) Place the asylum trim assembly 2A on the door so that spindle engages with the mortise lock and fasten with (4) 8-32 screws (item 4).
Test the knob for latch retraction. If latch does not extend loosen both 10-32 screws (item 5) to readjust alignment and re-tighten.
E) Place the asylum cover (item 2C) on the asylum trim assembly and screw together with (4) 8-32 screws (item 3).
