background image

xFUME

®

 ABIROB

®

 AF500

10 Disassembly

EN 

-

 15

10 Disassembly

1

Disconnect the cable assembly from the wire feeder.

2

Remove the parts to be disconnected (change body, bracket, torch neck).

11 Disposal

11.1 Disposing of materials

This product is mainly made of metallic materials that can be melted in steel and iron works and are thus 
almost infinitely recyclable. The plastic materials used are labeled in preparation for their sorting and 
separation for later recycling.

11.2 Disposing of consumables

Oil, greases and cleaning agents must not contaminate the ground or enter the sewage system. These 
substances must be stored, transported and disposed of in suitable containers. Contaminated cleaning tools 
(brushes, rags, etc.) must also be disposed of in accordance with the information provided by the 
consumables’ manufacturer.
► Observe the relevant local regulations and disposal instructions in the safety data sheets specified by 

the manufacturer of the consumables.

The disposal of dust collecting bags and disposal bags is subject to special waste regulations. The dust must 
not enter sewage systems or be disposed of together with normal household waste.
► Observe the local and official regulations.

CAUTION

Risk of injury due to unexpected start

If power is supplied during maintenance, cleaning or disassembly, parts can start running unexpectedly 
and lead to injuries.
► Switch off the device.
► Close all supply lines.
► Disconnect the electrical power supply.

Equipment marked with this symbol is covered by European Directive 2012/19/EU on 
waste electrical and electronic equipment (WEEE).
► Do not dispose of electrical and electronic equipment with household waste.
► Disassemble electrical equipment prior to proper disposal.

10 Disassembly on page EN

-

15

► Collect components of electrical separately and recycle in an environmentally 

responsible manner.

► Observe local regulations, laws, provisions, standards and guidelines.
► Please consult your local authority for information about collection and return of 

electrical devices.

Summary of Contents for xFUME AF500

















Reviews: