Ability 1030B User Manual Download

Page: 30 / 32

Shortcuts at default

User’s manual

Appendix B

SHORTCUTS AT

DEFAULT

description

function

parameter

Arm/disarm

Applies a pre-set scenario

Scenario

Stop alarms

Immediately deactivates the outputs

relative to zone/partition alarm and

tamper events and system tamper

events.

Clear call queue

Cancels the call queue and stops ongoing

calls (if any).

Delete memory

Carries out a “Stop alarms” operation

and, at the same time, deletes memory of

system and partition alarm and tamper

events.

Activate outputs

Activates one of the programmed outputs.

Output

Deactiv. outputs

Deactivates one of the programmed

outputs.

Output

Overtime

Delays auto-arming time of partitions by

30 minutes.

Teleservice req.

Sends a call to the Installer company

number (Teleservice number).

Arm/disarm menu

Accesses the User Menu section: Arm/

Disarm

Alarm menu

Accesses the User Menu section: Manage

alarms

Activations menu

Accesses the User Menu section:

Activations

View menu

Accesses the User Menu section: View

Keypad sett.menu

Accesses the User Menu section:Keypad

Keypad

ZoneBypass menu

Accesses the User Menu section:

Activations/Zones

Output control

Accesses the User Menu section: Outputs

ON/OFF

Enab.teleservice

Accesses the User Menu section:

Activations/Teleservice

Enable codes

Accesses the User Menu section:

Activations/Codes

Enable keys

Accesses the User Menu section:

Activations/Keys

Enable timers

Accesses the User Menu section:

Activations/Timers

Enab. auto-arm

Accesses the User Menu section:

Activations/Auto-arm

View events log

Accesses the User Menu section: View/

Events log

View alarm log

Accesses the User Menu section: View/

Alarms log

View faults log

Accesses the User Menu section: View/

Faults log

View arm ops log

Accesses the User Menu section: View/

Arm/Disarm ops.

ViewSystemStatus

Accesses the User Menu section: View/

System Voltage

View zone status

Accesses the User Menu section: View/

Zone status

Change PIN

Accesses the User Menu section: Change

Time/date setup

Accesses the User Menu section: Time/

Date

View faults

Accesses the User Menu section: View/

Faults

Summary of Contents for 1030B

































Search results

Summary of Contents for 1030B

Reviews:

Related manuals for 1030B

Brands by name

Popular brands

Ability 1030B, User Manual

Search results

Summary of Contents for 1030B

Reviews:

Related manuals for 1030B

Brands by name

Popular brands