background image

|     Installation  –   

Preparation for installing the PVEMH10 mounting plate

14

Preparation for installing the PVEMH10 mounting plate

If you are installing the PVEMH10 mounting plate, you will need to install the supplied coupling relay in the eMH1 

Wallbox and then establish a connection to the inverter of the PV system (see 

Steps 7

 to 

9

 in the section “Mechani-

cal installation of the wallbox on the mounting plate” from page 21 onwards).
When the PVEMH10 selector switch is set to 

ECO

, the inverter enables the charging process based on the power 

threshold set for the system in the 

ABL Configuration Software

.

NOTE

Information on the inverter and wiring

 

ƒ

Please read the operating instructions for your inverter before installation. All the requirements for the control 

cables as well as the permissible peak voltages for the control cables will be specified there.

 

ƒ

You’ll also be able to find out how to set the threshold value for enabling the charging process. The threshold 

value is the power at which the inverter enables charging in 

ECO

 charging mode.

 

ƒ

When selecting the threshold value, you should always take into account the size of the PV system, the 

average consumption for your own use and the charging power of the eMH1 Wallbox set in the 

ABL Config-

uration Software

Operation with an inverter with digital output

Can be used for inverters with a control output with switching voltages from 8 to 230 V AC/DC.

+A1

1(L)

-A2

2

N

PVEMH10

Relay

Inverter PV system

You must always provide an appropriate cable connection to the inverter at the installation location, which is then 

connected to the 

+A1

 and 

-A2

 contacts of the relay. The allocation is shown in the following table.

The connection itself is described in 

Step 7

 in section “Mechanical installation of the wallbox on the mounting plate” 

on page 21.

PVEMH10

Relay terminal

Relay contact

Inverter

Black wire 

1 (L)

+A1

 Relay control terminal A

Blue wire 

2

-A2

 Relay control terminal B

Summary of Contents for WHEMH10

































Reviews: