background image

|     Installation  –   

Preparation for installation on a wall

12

In addition, you will need the following components and tools:

 

ƒ

Electric drill

 

ƒ

Pencil

 

ƒ

8 mm 

 drill bit suitable for  

the respective mounting surface

 

ƒ

Spirit level

 

ƒ

Torx screwdriver

 

ƒ

Phillips screwdriver

 

ƒ

Pliers

 

ƒ

Utility knife

 

ƒ

Tape measure

 

ƒ

Scissors

 

ƒ

Hammer

Preparation for installation on a wall

A sufficiently dimensioned surface-mounted or concealed supply cable must be laid at the installation location in or-

der to establish an electrical connection to the eMH1 Wallbox. The supply cable is fed through the central opening in 

the mounting plate and can then be inserted into the eMH1 Wallbox for the electrical connection (see “Mechanical 

installation of the wallbox on the mounting plate” on page 19).

NOTE

Inserting a surface-mounted supply cable

If you wish to insert a surface-mounted supply cable into the mounting plate, you must open one of the six pre-

stamped plastic guides in the edge of the plate by cutting it on both sides with a cutter and then carefully break-

ing it out with pliers.

 

ƒ

There are two plastic guides on the top edge, two on the bottom edge and two in the middle of the side 

edges of the mounting plate.

DANGER!

Dangerous electrical currents

Always observe the 5 safety rules:

1

  Cut power source

2

  Secure all cut-off devices

3

  Verify absence of voltage

4

  Ground and short-circuit

5

  Cover or bar access to adjacent components under voltage

Summary of Contents for WHEMH10

































Reviews: