background image

 

1

2

3

4

5

7

6

8

9

10

11

12

13

17

18

19

20

21

25

23

28

24

26

27

47

42

43

41

40

40

39

38

37

36

35

34

46

50

56

49

52

53

54

48

33

30

31

29

22

32

55

51

NOTES:

DWG SCALE 1:3

1.

45

44

15

16

14

ITEM

TORQUE SETTING

in.-lbs. (Nm)

12

55-65(6.2-7.3)

35

16-20(1.8-2.3)

39

60-72(6.8-8.1)

41

36-48(4.1-5.2)

54

30-35(3.4-3.9)

IT

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19
20
21

22

23

24

25

26

27

28

29

30

31
32

33
34

35

36

37

38

39

40

41

42
43

44
45
46
47

48

49

50

51
52

53

54

55

56

Parts Page

LHAU150

LHAU1502.5

SAT  900 525 735

Summary of Contents for LHAU150

Page 1: ... be inclusive Study and com ply with all regulations 1 TOOL INTENT Tool shall be used only for purposes intended in its design 2 AIR SUPPLY Test and operate tools at 90 PSIG 6 2 Bar maximum unless tool is marked otherwise Use FRL 3 UNUSUAL SOUND or VIBRATION If tool vibrates or produces an unusual sound repair immediately for correction 4 OPERATOR PROTECTIVE EQUIPMENT Wear goggles or face shield w...

Page 2: ... DWG SCALE 1 3 1 45 44 15 16 14 ITEM TORQUE SETTING in lbs Nm 12 55 65 6 2 7 3 35 16 20 1 8 2 3 39 60 72 6 8 8 1 41 36 48 4 1 5 2 54 30 35 3 4 3 9 IT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Parts Page LHAU150 LHAU1502 5 SAT 900 525 735 ...

Page 3: ...BA0022 24 mm PAD WRENCH 1 33 NA 1 Back Up Pad supplied with each tool type determined by model 1 34 ABA0062 INTERNAL MUFFLER 1 35 ABA0087 MUFFLER BODY 1 36 ABA0009 VALVE SEAT 1 37 ABA0007 VALVE 1 38 ABA0014 VALVE SPRING 1 39 ABA0013 INLET BUSHING ASSEMBLY 1 40 ABA0044 O RING 2 41 ABA0006 SGV RETAINER 1 42 ABA0410 ASSEMBLY FOR 1 in 28 mm HOSE SuperVAC SGV SWIVEL EXHAUST 1 43 ABA0778 1 in 28 mm HOSE...

Page 4: ...0 PSI 6 2 Bar If run at lower pressure the performance of the tool is reduced 3 Always wear required safety equipment when using this tool 4 When sanding always place the tool on the work then start the tool Always remove the tool from the work before stopping This will prevent gouging of the work due to excess speed of the abrasive 5 Always remove the air supply to the sander before pad 6 aware o...

Reviews: