background image

 

 Part number 20079, Rev 0 

 

 

 

 
 
 

 

 
 
 
 
 
 
 
 
 
 

PREMIERE SOLID DOOR FREEZERS 

ABT-2020MP, ABT-2030MP, ABT-3020MP, ABT-3030MP, ABT-3020AP 

OWNER’S INSTRUCTIONS 

This manual describes how to operate and care for your appliance to get the best, most efficient, performance. 

READ THIS BOOK! 

Note to Customer: 

This merchandise was carefully packed and thoroughly inspected before leaving our plant.  Responsibility 
for its safe delivery was assumed by the carrier upon acceptance of the shipment.  As directed on the 
side of your packing carton, claims for loss or damage sustained in transit must be made on the carrier as 
follows: 
 
A.) 

Visible Loss, Damage, Shortage External Evidence of Loss or Damage: 

This type of damage 

must

 be noted on the freight bill and acknowledged by the carrier’s agent (driver) at time of delivery. 

Make sure you get a signed copy. Send a written request for an inspection to the carrier.  

B.) 

Concealed Damage

: This type of damage may not be discovered until  the unit is being unpacked. 

When concealed damage is discovered, stop unpacking immediately and contact the carrier 
immediately to report the claim and request an inspection. This should be done as soon as possible 
and, in any case, must be done within 15 days or receiving the merchandise. If at all possible, do not 
move the item and save all packaging material for carrier’s inspection.  

C.)  FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN THE CARRIER REFUSING TO 

HONOR YOUR COMPANY’S  CLAIM. UNDER NO CIRCUMSTANCES SHOULD THE 
MERCHANDISE BE RETURNED TO THE MANUFACTURER. NO RETURNS WILL BE ACCEPTED 
WITHOUT PRIOR AUTHORIZATION. 

 
 

 

Horizon Scientific 

125 Varnfield Drive 
Summerville, SC 29483 
Phone:  800-648-4041 
Fax:      843-821-8051 

Warranty: 

Two-Year Parts and Labor 
5 Years Compressor Parts 

Revision Date 

08/30/2012 

 

 

Summary of Contents for ABT-2020MP





















Reviews: