background image

Part number 20219, Rev 0 
 

12 

 

MAINTENANCE AND CLEANING 

These units require very little maintenance. They should be cleaned periodically to keep them 
running efficiently. Use the cleaning agents and suggestions below for best results.  

If ¼ to ½ inch of frost accumulates or if the unit will not maintain proper temperature, it should 
be defrosted per the procedure on page 14.  

CLEANING

 

PART 

CLEANING AGENTS 

TIPS AND PRECAUTIONS 

Interior and Door 
Liners 

Soap and water 
Baking soda and water 

Use 2 tablespoons of baking soda in 1 quart of 
warm water 
Be sure to wring excess water out of sponge or 
cloth before cleaning around controls, light bulb 
or any electrical parts. 

Glass Doors (if 
applicable) 

Soap and water 

Clean the glass with a mild detergent and water 
on a soft cloth or sponge. Rinse with water and 
wipe dry 

Door Gaskets 

Soap and water 

Wipe gaskets and their seating surfaces with a 
clean soft cloth 

Shelves 

Soap and water 

Do not wash removable shelves in dishwasher 

Exterior and 
Handles 

Soap and water 
Non Abrasive Glass 
Cleaner 

Do not use commercial household cleaners, 
ammonia, or alcohol to clean handles 
Use a soft cloth to clean smooth handles 
Do not use a dry cloth to clean smooth handles 

 
STAINLESS STEEL CARE AND CLEANING 

Use  the  proper  tools- 

When  cleaning  stainless  steel  surfaces;  take  care  to  use  non-abrasive 

tools.  Soft  cloths  and  plastic  scouring  pads  will  not  harm  the  steel’s  passive  layer.    Stainless 
steel pads may be used but be sure to always scrub in the direction of the polishing lines. 

Clean with the polish lines- 

Some stainless steels come with visible polishing lines or “grain”.  

When  visible  lines  are  present,  you  should  always  scrub  in  a  motion  that  is  parallel  to  them.  
When the grain cannot be seen, play it safe and use a soft cloth or plastic scouring pad. 

Use alkaline, alkaline chlorinated or non-chloride containing cleaners- 

While many traditional 

cleaners  are  loaded  with  chlorides,  there  is  now  an  ever  increasing  choice  of  non-chloride 
cleaners.  If you are not sure of your cleaner chloride content, contact your cleaner supplier.  If 
they tell you that your present cleaner contains chlorides, ask if they have an alternative.  Avoid 
cleaners containing quaternary salts as they also can attach stainless steel and cause pitting and 
rusting. 

Summary of Contents for ABT-HC-UCBI-0420-ADA

















Reviews: