background image

Part number 20219, Rev 0 
 

 

INSTALLATION INSTRUCTIONS 

 

UNCRATING  

Move  your  refrigerator  as  close  to  the 

final  location  as  possible  before 
unpacking.  Remove  the  carton  and 
the  styrofoam  strips.    The  location 
should  be  as  close  as  possible  to  the 
power  outlet  so  no  extension  cord  is 
needed.  

LEVELING 

 You  can  level  your  unit  with  the  screw-

type adjustable leveling legs on the front corners of the unit.  Turn counterclockwise to raise 
the  corner;  turn  clockwise  to  lower  it.  Leveling  legs  are  required  in  front  only.    Unit  may 
have a slight tilt from front to back. This is acceptable and is recommended on this unit. 

POWER SOURCE 

The  supply  circuit  to  this  cabinet  must 
conform to all National and Local Electrical 
Codes.    Consult  the  cabinet  Serial-Data 
plate  for  voltage,  cycle,  phase,  and  amp 
requirements  before  making  connection. 
VOLTAGE SHOULD NOT VARY MORE THAN 
5%  FROM  SERIAL  PLATE  RATINGS.    A 

separate circuit is recommended to prevent possible loss of 
product  due  to  over-loading  or failure  of  other equipment 
on the same circuit.  PROTECT THE CIRCUIT WITH A 20 AMP 
DELAY-TYPE  FUSE  OR  CIRCUIT  BREAKER.    Do  not  use  an 
extension  cord.    Be  sure  your  unit  is  properly  grounded.  
Use  the  3-prong  plug  provided  into  a  3-prong  grounded 
outlet.  (Only  this  method  complies  with  national  electrical 
codes,  local  codes  and  ordinances.)    Unless  the  above 
grounding  method  is  followed,  you  are  not  protected 
against severe or lethal shock in the event of a short circuit 
of an electrical component or wiring of the unit. 

Summary of Contents for ABT-HC-UCBI-0420-ADA

















Reviews: