background image

Absco Industries

Assembly Instruction Manual

ABSCO SKILLION CARPORT

MODEL: CPDN2

5.50mW x 5.50mD x 2.37mH

Model: CPSN2

25/11/22

18  

 

 

Absco Sheds Storage Guidelines

•  Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme 

weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, 
screw fi xings etc., may exhibit minor deformations which may allow some water entry. These areas should be 
checked regularly to ensure that maximum strength and protection is maintained.

•  Other weather conditions such as extreme heat and extreme cold, moist or dry air can infl uence the effects 

of concrete fl oor moisture and/or condensation on the underside of the roof sheets.

•  Absco Sheds and storage units are primarily used for storage of garden equipment such as lawnmowers, 

wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions 
may require additional protection such as being sealed or covered by plastic sheets and/or stacked above 
the concrete fl oor on timber slats.

•  Waterproof sealants may be used to offer further protection where required around joins and screw fi xings, 

as can rubber door seals and other products which are available from most hardware outlets.

•  Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not 

recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting 
with water accumulating and being trapped inside the shed.

•  Absco accepts no responsibility for water entry, fl oor moisture, condensation or the condition of the Contents 

inside your Absco steel building arising from any of the pre-mentioned weather conditions.

6-12 Activity St, Acacia Ridge QLD 4110

PO Box 119, Acacia Ridge QLD 4110

AU: 1800 029 701

N Z: 0800 466 444

admin@absco.com.au

www.abscosheds.com.au

Summary of Contents for SKILLION CPSN2





















Reviews: