background image

This warranty does not apply to surface deterioration of panels caused by 'Swarf” (Tiny particles of steel debris left from cutting,

replacement or refund for a major failure and for compensation for any other foreseeable loss or damage. You are also entitled

three business days to advise you of the assessment outcome of the claim, which may include your expenses incurred in making

ABSCO SHEDS - STORAGE GUIDELINES

ABSCO SHEDS include garden sheds, garden beds, storage units, aviaries, garages, awnings and carports.

ABSCO SHEDS are designed to be weatherproof for normal weather conditions. In the event of extreme weather

conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings

etc., may exhibit minor deformations which may allow some water entry. These areas should be checked

regularly to ensure that maximum strength and protection is maintained.

Other weather conditions such as extreme heat and extreme cold, moist or dry air can influence the effects of

concrete floor moisture and/or condensation on the underside of the roof sheets.

ABSCO SHEDS and storage units are primarily used for storage of garden equipment such as lawnmowers,

wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions

may require additional protection such as being sealed or covered by plastic sheets and/or stacked above the

concrete floor on timber slats.

Waterproof sealants may be used to offer further protection where required around joins and screw fixings, as

can rubber door seals and other products which are available from most hardware outlets.

Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not

recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting with

water accumulating and being trapped inside the shed.

Absco accepts no responsibility for water entry, floor moisture, condensation or the condition of the Contents

inside your Absco steel building arising from any of the pre-mentioned weather conditions.

ABSCO INDUSTRIES

ASSEMBLY INSTRUCTION MANUAL

CARPORT MODEL: CPSW50 

10-05-2017  

      

Absco Industries

Skillion Carport Model: CPSW50

PAGE 35

Summary of Contents for CPSW50



















Reviews: