background image

 

 

ABUS TECHNOLOGIES INC.

 

 

 

PT

 

 

 

4.  ORDERING DETAILS 

 

TYPE 

DESCRIPTION 

Type 

PT10 

Absolute Pressure Transmitter 

0 ~ 25 bar 

PT20 

Gauge/Compound Pressure Transmitter 

-1 ~ 0 ~ 1800 bar 

PT30 

Vacuum Pressure Transmitter 

-760 ~ 0 mmHG 

Range 

 

__ 

 

Specify Range code 

Output 

 

 

4 ~ 20 mA 

0 ~ 10 V 

Others, specify 

Process 

Connection 

 

 

G 1/4” 

G 1/2” 

1/4” NPT 

Others, specify 

Electrical 

Connection 

 

 

DIN Connector (Hirschman Type) 

Thread Screw 

Bendix Connector 

Direct Down-lead 

Integral 

Indicator (Refer 

LPI-PT) 

 

+ LPI-PT 

 

Loop Powered Indicator 

W/O Indicator 

Zero and Span 

Adjustment 

 

 

With Internal Z & S 

W/O 

Example: PT20 >10 > D > 1 > W > LPI-PT > 1 

STANDARD RANGES FOR PT SERIES 

CODE 

GAUGE/ABS. PRESSURE 

CODE 

COMPOUND 

01 

1.00 bar 

17 

600.00 bar 

02 

1.60 bar 

18 

1000.00 bar 

03 

2.50 bar 

19 

1500.00 Bar 

04 

4.00 bar 

20 

1800.00 Bar 

05 

6.00 bar 

 

 

06 

10.00 bar 

 

COMPOUND 

07 

16.00 bar 

41 

-1 ~ 0.6 bar 

08 

20.00 bar 

42 

-1 ~ 1.0 bar 

09 

25.00 bar 

43 

-1 ~ 2.0 bar 

10 

40.00 bar 

44 

-1 ~ 3.0 bar 

11 

60.00 bar 

45 

-1 ~ 5.0 bar 

12 

100.00 bar 

46 

-1 ~ 9.0 bar 

13 

160.00 bar 

 

 

14 

200.00 bar 

 

VACUUM 

15 

250.00 bar 

61 

-760 ~ 0 mm/Hg 

16 

400.00 bar 

 

 

CUSTOMIZED RANGES & UNITS - MARK 00 AS THE CODE, SPECIFY 

RANGE AND UNIT AT THE END OF PART NO. 

Example: PT20 >00 > D > 1 > W >0 > 0 >0-50 PSI

  

Table 1 

Summary of Contents for PT Series












Reviews: