background image

 

English 

 

Information on handling batteries 

 

Make sure that batteries are kept away from small children. Children may put batteries in their 
mouths and swallow them. This can cause serious harm to their health. If this happens, consult 
a doctor immediately.

 

 

Do not charge normal batteries, heat them up or throw them into naked flames (they may 
explode). 

 

The battery must not be directly exposed to heat or sunlight, and must not be stored in a place 
with a very high temperature. 

 

The battery must not come into contact with water. 

 

The battery must not be dismantled, pierced or otherwise damaged. 

 

The battery contacts must not be short-circuited. 

 

Change low batteries in good time. 

 

Always change all the batteries at the same time and use batteries of the same type. 

 

Leaky or damaged batteries can cause chemical burns on contact with the skin. In this case, 
wear protective gloves. Clean the battery compartment with a dry cloth. 

 

Important information on battery disposal 

Batteries with this label do not contain harmful substances such as cadmium, lead and 
mercury. However, used batteries must not be disposed of along with household waste 
in accordance with the battery directive. To protect natural resources and promote the 
recycling  of  materials,  separate  the  batteries  from  other  waste  and  deposit  them  at a 
local recycling center.  An additional  label  with the chemical symbols for Hg, Cd or Pb 
means that the batteries contain quantities of mercury, cadmium or lead which exceed 
the  restrictions  set  by  the  EU  Directive  2006/66/EG.  If  batteries  are  not  disposed  of 

properly, these substances can cause harm to human health or the environment 

 

Cleaning 

 

Dusty devices must be cleaned. You can clean dust from the air vents using a vacuum cleaner 
or compressed air. If necessary, you can remove the dust with a brush. 

 

You can clean the surface using a cloth slightly dampened in soapy water. Only use suitable 
microfiber cloths for high-gloss surfaces. 

 

Do not allow water to penetrate the device. 

 

Do not clean the device in a dishwasher. 

 

Do not use sharp, pointed, abrasive or corrosive cleaning materials or hard brushes. 

 

Do not use chemicals. 

 

Do not use flammable liquids for cleaning the device.  

 

Information on device disposal 

Important:  The  EU  Directive  2012/19/EU  regulates  the  proper  return,  treatment  and 
recycling  of  used  electronic  devices.  This  symbol  means  that  in  the  interest  of 
environmental protection the device must be disposed of separately from household or 
industrial  waste  at  the  end  of  its  service  life  in  accordance  with  applicable  local  legal 
guidelines. Disposing of used devices can be done at official recycling centers in your 
country. Obey  local regulations  when disposing of material. Further details on returns 
(also  for  non-European  countries)  can  be  obtained  at  your  local  authority.  Separate 

collection and recycling saves natural resources and ensures that all the provisions for protecting health 
and environment are observed when recycling the product. 

 

 

Summary of Contents for SHLM10000











Reviews: