background image

 

English 

 

2.2.  Operating 

Do not dim the LED bulb via the supply voltage (e.g. dimmer switch) but use the App or compatible Z-
Wave wireless switches/dimmer. 

Make sure that the power supply of the LED lamp is always switched on (e.g. wall switch ON), as this 
is the only way the device can function. 

 

2.3.  Exclusion / Remove Device 

 

 

Click the - (Remove) button in  your Z-Wave App and 
follow the further instructions 

 

Switch the LED bulb on. 

 

The App will show if the Remove device process was 
successful. The LED bulb will flash once and then dim 
to 5% 

 

 

Repeat the exclusion process if it was not successful. 

 

2.4.  Reset (Factory-Reset)  

 

 

Switch the Power supply oft he LED bulb ON and OFF 
6 times in a row. (Interval of 0.5 to 2 seconds) 

 

When  switched  on  for  the  6th  time,  the  LED  bulb 
flashes  twice  indicating  successful  reset  to  factory 
settings. 

 

Note:  

This  procedure  should  only  be  used  if  the  primary 
gateway is not capable of acting.  

If the device is set to the factory setting, the status is 
set  to  "not  included",  the  association  settings  and 
possible configurations are reset to default. 

 

Summary of Contents for SHLM10000











Reviews: