background image

 

66

3. 

DOME SET – MANUAL SPEED 

Manual Speed of Pan/Tilt is selectable from 100°/sec up to 200°/sec. The default setting is 
150°/sec. 

4. 

DOME SET – AUTO FLIP 

Auto Flip is available. Move joystick rightwards or leftwards for selecting ON or OFF. The 
default setting is OFF. This feature also can be enabled with 67 + preset button. 

5. 

DOME SET – ZOOM SPEED 

Zoom speed is selectable between FAST or SLOW mode. Move joystick to the right direction 
for selecting FAST or SLOW. The default setting is FAST. 

6. 

DOME SET – ALARM 

All alarms inputs are available after set as ENABLE. Move joystick to the right or left 
direction to select ENABLE/DISABLE. The default setting is DISABLE and this feature can 
be enabled with 97 + PRESET button. 

7. 

DOME SET – LANGUAGE 

Several languages are available: German, English, French, Dutch and Danish. Move joystick 
rightwards or leftwards to select language. The default setting is GERMAN. 

 
 
 
 
 
 
 
 
 
 
 
 

8. 

DOME SET – [NEXT PAGE] – SYSTEM LOCK 

Password protection helps to keep stored settings. It prevents changes by anybody without 
password. In order to enter [PASSWORD] page, system lock status must be ON. Move 
joystick to rightwards or leftwards to select ON. The default setting is OFF. 

 DOME 

SET 

 
SYSTEM LOCK:     OFF 
[PASS WORD] 
[OSD DISPLAY] 
[SYSTEM STATUS] 
[INITIALIZATION] 
[PREVIOUS PAGE] 

DEFAULT SETTING 

Summary of Contents for TVCC75100









































Reviews: