background image

1. Compliant fall protection and emergency rescue systems help prevent serious injury

during fall arrest.  Users must read and understand the 

User Instructions

 provided with

the product and be properly trained by their employer prior to use per OSHA 29 CFR
1910.66 and 1926.503 or applicable local standards.  

Misuse or failure to follow warnings

and instructions may result in serious personal injury or death.

2. Failure to follow all instructions and limitations on the use of Full Body Harnesses may result

in serious personal injury or death.

3. Minors, pregnant women and anyone with a history of either back or neck problems should

not use this equipment.

4. Not all fall protection components are rated for the same user weight capacity.  Only use

components rated for the same weight capacity.

5. Before using a personal fall arrest system, employees must be trained in accordance with the

requirements of OSHA 29 CFR 1910.66 in the safe use of the system and its components.

6. Personal fall arrest systems, including Full Body Harnesses, must be inspected prior to

each use for wear, damage, and other deterioration, and defective components must be
immediately removed from service in accordance with the requirements of OSHA 29 CFR
1910.66 and 1926.502.

7. Do not use or install equipment without proper training from a “competent person” as defi ned

by OSHA 29 CFR 1926.32(f).

8. Failure to have the leg straps of a Full Body Harness properly adjusted in the event of a fall

arrest may result in serious personal injury or death.

9. The additional length of the D-ring extender must be taken into consideration during the

clearance calculation process.

10. Never attach the unused leg of the lanyard back to the Full Body Harness at any location

other than an approved lanyard storage keeper.

11. Store Full Body Harnesses in a cool, dry, clean environment, out of direct sunlight, when not

in use.

12. After a fall occurs, or if any part of the load indicator warning is showing, the Full Body

Harness must be removed from service and destroyed immediately.

13. If inspection reveals any defect, inadequate maintenance, or unsafe condition, remove from

service and destroy.

14. Only 3M, or persons or entities authorized in writing by 3M, shall make repairs or alterations

to the equipment.

GENERAL SAFETY INFORMATION
Under Penalty of Law

These 

User Instructions

 are not to be removed except by the user of this equipment.  Current 

User Instructions

 must always be available to the user.  

WARNING

1. If an energy absorbing lanyard is used in conjunction with a cross-arm strap anchorage

connector, other anchorage extension, vertical lifeline, or horizontal lifeline, the additional
length of the anchorage connector, or sag from the lifeline must be taken into consideration

CAUTION

2

actoolsupply.com

actoolsupply.com

Summary of Contents for 3M Full Body Harnesses


















Reviews: