ACC WF-100 Smartouch Wifi Installation And Operational Manual Download

Page: 3 / 13

ACC Wifi Module WF-100 Installation

Module Installation:

1. Make sure power is off to the spa before proceeding!

2. If this is a new complete control system installation, skip this step and go to step 4.
3. Open up the Smartouch Digital control box and disconnect the existing spaside control panel

cable from the circuit board connector by firmly (but carefully) spreading the 2 levers on each
side at the same time.

4. Open up the ACC Wifi module WF-100 by removing the 4 corner screws on the back. (do not

remove the single screw located near the middle if present.)

POWER MUST BE TURNED OFF AT THE BREAKER WHEN CONNECTING THE WIFI

CONTROLLER.

AVOID ROUGH HANDLING THE RIBBON CABLE DURING INSTALLATION DO NOT PINCH OR

CRIMP THE CABLE.

IT IS NOT RECOMMENDED TO HAVE THIS CABLE EXPOSED TO DIRECT SUNLIGHT IN A

PERMANENT INSTALLATION.

DO NOT INSTALL THE WIFI CONTROLS BEHIND THE SPA SINCE WATER BLOCKS THE WIFI

SIGNAL AND ACTS AS A BARRIER BETWEENTHE ROUTER AND THE WIFI CONTROLS.

Summary of Contents for WF-100 Smartouch Wifi














Search results

Summary of Contents for WF-100 Smartouch Wifi

Reviews:

Related manuals for WF-100 Smartouch Wifi

Brands by name

Popular brands

ACC WF-100 Smartouch Wifi, Installation And Operational Manual

Search results

Summary of Contents for WF-100 Smartouch Wifi

Reviews:

Related manuals for WF-100 Smartouch Wifi

Brands by name

Popular brands