background image

31 

(3)

 

Heating:  Outdoor air temperature 7°C DB 6°C WB; inlet/outlet temperature 30/35°C. 

(4) Heating:  Outdoor air temperature 7°C DB 6°C WB; inlet/outlet temperature 40/45°C. 
(5) Cooling:  water temperature inlet/outlet 12/7°C. 
(6) Heating:  normal climatic condition; Tbiv=-7°C; eater temperature inlet/outlet 30/35°C. 

(7) The data are only indicative and subject to change. For the correct data, refer to the technical label sticked on the unit.

(8) Calculated in the case of the plant water temperature decrease with 15°C for 6 minutes of defrosting operation.

(9) Power sound: condition (3); the value is determined based on the measurements taken in accordance with the UNI EN ISO 9614-2, in compliance with the

requirements of Eurovent certification. The data with installed accessories SL or SSL are also reported. 
(10) The sound pressure value is calculated from the sound power level in accordance with ISO 3744: 2010, referred to 10 m away from the unit. The values with
installed accessories SL or SSL are also reported. 

(11) Packing’s height includes the pallet. 
(*) The available pressure head and characteristics of the pump refer to “CI1” kit for all sizes except 0270 for which the data are expressed for “CI6” kit 

N.B. The performance data are indicative and could be subject to change. In addition, the performances declared in apex (1), (2), (3) and (4) refer to the

instantaneous power according to EN 14511. The declared data stated in the apex (5) and (6) is determined according to the UNI EN 14825. 

WARNING: The minimum temperature allowed for storing the unit is 5°C.

 

13.2

 

LT VERSION 

TECHNICAL CHARACTERISTICS

 

Unit 

Model i-HP LT 

0125 

0125 

Integrated 

circulator 

0235 

0235 / 0235 

Integrated 

circulator 

0250 

0250 

Integrated 

circulator 

Cooling 

Cooling capacity  (1) 

kW 

21,00 

21,13 

28,40 

28,55 

36,10 

36,32 

Power input  (1) 

kW 

6,44 

6,22 

8,61 

8,36 

12,45 

12,08 

EER (1) 

W/W 

3,26 

3,40 

3,30 

3,42 

2,90 

3,01 

Cooling capacity (2) 

kW 

30,67 

30,78 

36,37 

36,49 

47,56 

47,76 

Power input  (2) 

kW 

7,34 

7,15 

8,91 

8,72 

12,52 

12,17 

EER. (2) 

W/W 

4,18 

4,31 

4,08 

4,18 

3,80 

3,92 

SEER (5) 

W/W 

3,98 

4,17 

3,90 

Water flow rate (1) 

L/s 

1,00 

1,01 

1,36 

1,37 

1,73 

1,74 

Load losses  user’s side heat exchanger (1) 

kPa 

32 

37 

20 

Heating 

Heating capacity (3) 

kW 

24,15 

24,02 

32,50 

32,36 

47,78 

47,58 

Power input (3) 

kW 

5,79 

5,57 

7,99 

7,76 

12,15 

11,81 

COP (3) 

W/W 

4,17 

4,32 

4,07 

4,17 

3,93 

4,03 

Heating capacity (4) 

kW 

23,76 

23,63 

32,50 

32,36 

45,10 

44,89 

Power input (4) 

kW 

6,88 

6,66 

9,97 

9,74 

13,56 

13,20 

COP (4) 

W/W 

3,45 

3,55 

3,26 

3,32 

3,33 

3,40 

SCOP (6) 

W/W 

4,02 

4,04 

3,81 

Water flow rate (4) 

L/s 

1,14 

1,13 

1,56 

1,55 

2,16 

2,15 

Load losses  user’s side heat exchanger (4) 

kPa 

37 

47 

34 

Energetic class: Water temp. 35°C / 55°C 

Classe 

A++ / A++ 

A++ / A+ 

A++ / A+ 

Compressor 

Type 

Scroll DC Inverter 

Scroll DC Inverter 

Scroll DC Inverter 

Rfrigerant oil (type) 

FV50S 

FV50S 

FV50S 

Numbert 

Refrigerant oil (quantity) 

mL 

2300 totale 

3800 totale 

4600 totale 

Refrigerant circuits 

Refrigerant 

Type 

R410A 

R410A 

R410A 

Refrigerant quantity (7) 

kg 

10,5 

11,2 

20 

Equivalent amount of CO2 (7) 

ton 

21,92 

23,39 

41,76 

Design pressure (high/low) 

MPa 

4,15/2,7 

4,15/2,7 

4,15/2,7 

Fan motor 

Type 

DC Brushless Motor 

DC Brushless Motor 

DC Brushless Motor 

Number 

Rated power input (1) 

kW 

0,6 

0,72 

1,10 

Max power input 

kW 

1,45 

1,5 

1,78 

Max current input 

2,1 

2,17 

2,57 

Rated air flow 

m

3

/s 

3,90 

4,10 

6,94 

Internal heat 

exchanger 

Internal heat exchanger type 

A piastre 

A piastre 

A piastre 

Number 

Water content 

2,2 

3,3 

4,1 

Hydraulic circuit 

Water flow (1) 

L/s 

1,00 

1,01 

1,36 

1,37 

1,73 

1,74 

Available head pressure (1) * 

kPa 

88 

75 

91 

Water content in the hydronic circuit 

3,3 

4,5 

6,0 

Hydronic kit Max pressure (calibration of 

relief valve) 

bar 

Hydraulic connections 

inch 

2"F 

2"F 

2"F 

Minimum volume of water (8) 

90 

108 

151 

Pump rated power input (1) 

kW 

0,28 

0,31 

0,44 

Pump max power input 

kW 

0,31 

0,31 

0,55 

Pump max current input 

1,37 

1,37 

2,05 

Energy Efficiency Index (EEI) 

≤ 0,23

 

≤ 0,23

 

≤ 0,23

 

Noise livel 

Sound power (9) 

dB(A) 

72,5 / SL 70,7 / SSL 69,8 

75,5 / SL 73,7 / SSL 72,8 

78 / SL 76,2 / SSL 75,3 

Sound pressure (10) 

dB(A) 

56 / SL 54,2 / SSL 53,9 

59 / SL 57,2 / SSL 56,9 

61,4 / SL 59,6 / SSL 58,5 

Electrical data 

Power supply 

400V/3P+N+T/50Hz 

400V/3P+N+T/50Hz 

400V/3P+N+T/50Hz 

Max power input 

kW 

14,83 

15,14 

19,16 

19,47 

28,62 

29,09 

Max current input 

21,4 

21,9 

27,7 

28,1 

41,4 

42,1 

Summary of Contents for HPE 35









































Reviews: