Accu-Steam GG24A, Installation & Operator'S Manual

Accu-Steam™ Gas G2 Installation and Operators Manual

MP5017-1702

PAGE 20

INSTALLATION  

Use a spirit level resting on the appliance cooking 

surface to ensure it is level front-to-back and left-

to-right.
TABLE TOP
Install the (4) rubber foot tips provided with your 

appliance onto the four foot adjusters of each 

of the commercial appliance legs. This will keep 

the griddle from sliding on the counter-top under 

normal use. Once the rubber foot tips have been 

installed, adjust the four foot adjusters up or 

down as needed to level the griddle side to side 

and front to back.

ACCUTEMP STAND 

If on an AccuTemp griddle stand with casters, 

ensure that the floor surface is level and place 

the two locking casters to the “on” position 

and follow the leveling instructions to verify the 

appliance is level.

ELECTRICAL SUPPLY

The ACCU-STEAM™ griddle has been designed, 

manufactured and tested to meet or exceed the 

demanding standards of safety set forth by 

ANSI 

Z83.11.

  To to ensure that this high level of safety 

is maintained in your installation, it is important 

that you read and understand the following 

information before attempting to plug in your 

griddle.
ELECTRICAL REQUIREMENTS

Electrical requirements are listed on the data 

plate located on the front right of the control 

panel. All standard AccuTemp griddles are 

supplied with a 6ft (1.83m) cord and the 

appropriate UL listed plug that must be connected 

to a 15 Amp (120Vac) or a 20 Amp (208-240Vac) 

depending on the rating listed on the data 

plate. Make sure that the voltage at your supply 

receptacle is within ± 10 % of the voltage listed 

on the griddle data plate. Connection to any other 

voltage may cause damage to components in the 

commercial appliance. The appliance plug must 

be used with the appropriate receptacle. 
Direct wiring will void the warranty.

GROUNDING INSTRUCTIONS

Grounding provides a path for electric current to 

reduce the risk of shock. This product is equipped 

with a power cord having a grounding conductor 

and a grounding plug. The plug must be plugged 

into a grounded receptacle that is installed and 

grounded in accordance with local codes, or in 

the absence of local codes, with the 

National 

Electric Code, NFPA 70, or the Canadian 

Electrical Code, CSA22.2

, as applicable.

 Under no circumstances shall the grounding 

or prong of the plug be cut off or bent to fit a 

receptacle other than the one supplied. Do not 

use any adapters to fit the receptacle.

GAS CONNECTION

This appliance has been manufactured for use 

with the type of gas indicated on the data plate.

(See Fig. 3) If the locations gas supply does not 

match the gas indicated on the equipment data 

plate. Contact  AccuTemp Products Technical 

Service at (800) 480-0415
All gas connectors must be in accordance with 

the local code, State and 

National Fuel Federal 

Gas Codes, ANSI Z223.1

The equipment should have a separate gas 

shutoff valve (not supplied) installed in the 

equipment supply line. A 1/2”  inside diameter 

or larger gas supply line or an 

ANSI 

approved 

commercial flexible gas hose that the inside 

diameter is 1/2” or larger this to insure adequate 

volume of gas for the equipment. The facility 

supply manifold and regulator must be sized to 

the load of all the appliances connected to it. 

If other appliances are connected to the same 

supply line as this equipment the gas load must 

When this appliance is installed with casters 

it must be installed with the casters supplied. 

A connector complying with either ANSI 

Z21.69 - CSA 6.9. It must also be installed with 

restraining means to the connector as specified 

in the appliance manufacturer’s instructions.

WARNING