SUPPLIED ACCESSORIES:
HOW TO USE THE PARTS COUNTING FEATURE
1) To set your balance to parts counting mode, scroll through the
weighing modes by pressing the CAL/MODE keypad until a down
facing arrow appears in the lower left corner on the display. The
minimum parts quantity number (5) will also be displayed as a
flashing number.
2) Continue to press the CAL/MODE keypad to select the desired
parts counting unit: 5, 10, 25, 50 pieces. After "50" is dis-
played, the indicator will scroll back to the gram weighing mode.
3) With the selected parts counting unit still flashing, place the
desired sample on the weighing pan. Allow the sample to stabilize
for 3-5 seconds then press OFF. The parts counting function is now
set for the selected 5, 10, 25, 50 piece quantity.
IMPORTANT: Minimum individual (1 piece) part weight must be
greater than or equal to 5X "D" ("D" is the division or graduation of
the balance). If the sample unit weight for one piece is less than 5X
"D" the display will read "Er 1", indicating that the individual
(1 piece) part weight is too low and must be increased. To reset,
press CAL/MODE and scroll through the weighing modes again to the
desired parts counting value. Refer to the following chart for mini-
mum unit part weight (1 piece) for your particular balance.
B
alance
G
raduation
P
art
W
eight
M
inimum
(1
piece
)
SV-30
0.005 kg
0.025 kg
SV-50
0.01 kg
0.05 kg
SV-100
0.02 kg
0.1 kg
AC Adapter
#AC-1 -For use in USA/Canada (AC 120V 60Hz)
#AC-2 -For use in Europe (AC 230V 50Hz)
#AC-3 -For use in U.K. (AC 240V 50Hz)
#AC-4 -For use in Japan (AC 100V 50/60Hz)
#AC-5 -For use in AUS/NZ (AC 240V 50Hz)
MINIMUM WEIGHING LIMITATION:
Because the SV-Series is designed to be a heavy capacity balance,
minimal initial loads may not produce a response from the balance.
The minimum initial increment applied to each model should be 50
grams or more. Initial weighing loads may not produce the minimum
excitation voltage to produce weight readings.
Instruction
Manual
PLEASE READ COMPLETE INSTRUCTIONS BEFORE USE
Platform
LCD Display
Detachable Cord
AC Adapter Input
Membrane
9V Alkaline Battery Compartment
S
pecifications
M
odels
SV-30
SV-50
SV-100
Capacity (kg, lbs)
30 kg/66 lbs
50 kg/110 lbs
100 kg/220 lbs
Readability (kg, lbs)
0.005 kg/0.01 lbs 0.01 kg/0.02 lbs 0.02 kg/0.05 lbs
Repeatability
±2d
Weighing Modes
kg, lb & parts counting presets of 5, 10, 25 & 50 pieces
Tare Range
To capacity by subtraction
Calibration
(NBS Class F)
30kg
50kg
100kg
Stabilization Time
(sec)
3
Maximum Overload
200.0%
Overload Indication
"E" with audio tone
Underload Indication
Negative value
Auto Off
4 minutes no activity (battery only)
Optimum Operating
Temperature
64˚û - 77˚û F (18-25 C)
Optimum Operating
Humidity
Less than 80% RH
Display Type
LCD/.75" high w/segment test
Audio Tone
On, start up, function keys, overload, low battery
Low Battery Indication
"LO" w/10 beep signal
Power Requirements
9V alkaline or nicad battery, or included AC adapter
Platform Size/Type
12" x 12.5"stainless steel (305 x 315mm)
Dimensions HxWxD
4"x 14.5"x 18.5"(100 x 370 x 470mm)
Net Weight (lb/kg)
12/5.4
Optional Accessories
Calibration mass
Performance specifications measured within optimum temperature range
after recommended warm up and proper calibration. Specifications subject
to change without notice.
as applicable
Models SV
Models SV-30
-30 SV
SV-50
-50 SV
SV -100
-100
Models
Models SV
SV-30
-30 SV
SV -50
-50 SV
SV -100
-100
Certificate
of Calibration
We hereby certify that this instrument
was manufactured in the United States
and that it has been calibrated using
appropriate reference standards traceable
to the
National Institute of Standards
National Institute of Standards
and Technology.
and Technology.
This instrument has been fully
inspected and has passed all quality tests
as specified by
Acculab
Acculab quality procedures.
To assure proper measurements, it is
necessary to periodically recalibrate the
instrument using appropriate standards
as specified in the operating manual.
R
R
P
hone:
800-656-4400
631-254-4299
F
ax :
800-356-0338
631-253-5472
S
a les Office :
131 Heartland Blvd
Edgewood, NY 11717
www.acculab.com
400305.1 Rev. A
ACCULAB
ACCULAB
Limited Warranty
Effective Date: January 1, 2003
Standard Terms and Conditions
Models: SV series
ACCULAB warrants the product series "SV" against defects in material and
workmanship to the original consumer for a peroid of tewnty four (24) months
or a maximum of thirty (30) months from date of sale to Authorized
ACCULAB distributor. The warranty includes parts, labor and return shipping
charges to customer (ground freight).
This specific warranty shall not apply to any product damaged due to accident,
misuse, abuse, lightning strike, power surges, improper packaging for shipment to
ACCULAB, or service/modification by anyone other than an authorized ACCULAB
Technician.
The purchaser's sole remedy, ACCULAB and its suppliers sole liability are set forth
herein. In no event shall ACCULAB or its suppliers be liable for any damages,
incidental or consequential, expenses, lost profits, lost savings, or any other claims
due to the use or inability to use the product/s. ACCULAB shall limit its obligations
under warranty to a time not to exceed the original product warranty period set
forth herein. This warranty gives you specific legal rights and you may have other
rights, which may be different from state to state.
In the event that service is required, the Customer/Distributor should call
ACCULAB (800-656-4400, extension 8342) for proper return authorization. The
product must be delivered to ACCULAB, Service Division 6542 Fig Street, Arvada,
CO., 80004 within the warranty period, freight charges prepaid. The customer is
responsible for product removal, installation and proper packing in order to
prevent damage while shipping to ACCULAB Service facility.
This limited warranty supersedes all other warranties pertaining to the ACCULAB
products, whether expressed or implied. Claims may be made by calling 800-656-
4400/631-254-4299, by fax 800-356-0338/631-253-5472, or in writing to:
Attn: Warranty Administrator
6542 Fig Street
Arvada, CO., 80004
(800-656-4400)
