HDG-4000 HD/SD/DVI COMPONENT VIDEO CALIBRATION GENERATOR USER MANUAL
6
2
Output Indicator LEDs
YPbPr / 444 – Analog YPbPr and digital YCbCr 4:4:4 signals are selected. The
black level is set to 0-IRE (blanking level). Bi-Level sync is always used for 480i/p
or 576i/p. For 1080i/p or 720p, Tri-Level sync on Y (only) is used by default to
comply with EIA/CEA-770.3. (Bi-level sync can be selected in the OSD menu).
RGB Video – Analog RGB and digital RGB-Video signals are selected. The black
level is set to 0-IRE (blanking level). Analog HV sync polarity, or SoG can be
selected.
YPbPrs - Analog YPbPrs and digital YCbCr 4:2:2 signals are selected. The
analog output black level is set to 7.5-IRE. This mode is compatible with older
DVD players that include black-level setup on their 480i YPbPr output. It is also
compatible with scalers or video converters that output black at 7.5 IRE.
RGBs PC - Analog RGBs and digital RGB-PC signals are selected. The analog
output black level is set to 7.5-IRE. This mode is compatible with scalers or video
converters that output black at 7.5 IRE.
Y/C - Analog Y/C (S-video) signals are selected. Other analog signal outputs are
disabled. The analog black level is set to 7.5-IRE for 480i signals (default), but
there is no black level setup on 576i signals. The 480i black level setup can be
disabled in the OSD Output menu.
CVBS - Analog CVBS (Composite video) signals are selected. Other analog
signal outputs are disabled. The analog black level is set to 7.5-IRE for 480i
signals (default), but there is no black level setup on 576i signals. The 480i black
level setup can be disabled in the OSD Output menu.
3
Sync Selection
In the RGB or RGBs mode, press and hold the Output button for about 1 second
and the front panel HV Pos and Neg LEDs will change to indicate the RGB HV
sync polarity. Hold the Output button until both LEDs are off to select the SoG
mode. The RGB HV sync polarity or RGB SoG (sync-on-green) can also be
directly selected with dedicated buttons on the HDG-4 remote control.
Bi-level embedded sync for HD signals, and HV sync polarity for digital signals
can be selected in the OSD Sync menu.
4
50 Hz / 60 Hz Selection
Select 50 Hz modes (HDG-4000 L2 only) by pressing and holding the Format
button for about 1 second. When the 50 Hz LED illuminates release the Format
button. If you continue to hold the Format button the 50 Hz/60 Hz mode will
alternate about once per second.
5
Format Selector
Press and release the Format button to change the video format in the following
order - 1080i, 720p, SD i, SD p, 1080p60(50), 1080p24(25), and the 1080p User
format (when 60 Hz is selected). The User format can be selected in the OSD
Defaults menu to produce 1080p24sf, 1080p30, or 1080p48. All formats can be
selected directly using the HDG-4 remote control.
YPbPr also selects
digital YCbCr 4:4:4
signals.
RGB also selects
digital RGB-Video
signals.
YPbPrs also selects
YCbCr 4:2:2 signals.
RGBs also selects
RGB-PC signals.
Y/C (S-video) Video
CVBS (Composite)
Video
RGB Sync Polarity &
RGB Sync-on-Green
50 Hz / 60 Hz
Selection
480i, 480p, 720p
& 1080i formats
