background image

4-5

 4

 5

General Features

•   ACCUSPLIT X case with ergonomic design and 
  no-fail buttons

•   4 button operation

•   Large LCD display with contrast adjustment

•   12/24 hour display

•   Time of day and chime

•   Daily alarm

•   Full 1/100 second chronograph with working 
  range from 0 to 19 hr. 59 min. 59.99 seconds 
  with 500 memory records of split and lap time.

•   Recall function for recorded split and lap times

•   Count-Down timer with working range from 0 to 
  19 hr. 59 min. 59.9 seconds

•   Three operating modes (Countdown Repeat, 
  Countdown Stop, Countdown then count up) 
  for countdown timer

•   Stroke/Stride measurement basing on “3”

•   Speed measurement (AX602M500 Model only)

•   Decimal second, minute and hour chronograph 
  (AX602M500DEC Model only)

•   Beep sound selectable

•   Uses long life Lithium CR2032 battery for years 
  of use between battery changes

•   Low battery check

The operation of the stopwatch is divided into 
nine modes. As you choose each “mode”, a 
message will be displayed for a second before 
you enter the mode:

6-7

 6

 7

Button Operation

•  MODE 

- used to 

  change the watch’s 
  operating mode

•   START •  SPLIT 

- used 

  to start the timer or 
  stopwatch, and for taking 
  split and lap times

•  RECALL

 - used to recall recorded split 

  and lap times (memories)

•   STOP •  RESET 

- used to stop and reset the 

  stopwatch  or timer

TIME

Speed mode 

(AX602M500 only)

Normal Time  mode 

Alarm mode 

SPEED

ALARM

Chronograph mode 

CHRONO

LapTime Recall mode 

RECALL

Data mode 

DATA

Timer mode 

TIMER

Pacer mode 

PACER

Stroke Measurement 

STROKE

RECALL

SPLIT
or
STOP

Press MODE to cycle through:

Summary of Contents for AX602M500















Reviews: