background image

 

 

Refer all servicing to qualified service personnel. Servicing is required when the appliance has been 
damaged  in  any  way,  such  as  power-supply  cord  or  plug  is  damaged,  liquid  has  been  spilled  or 
objects have fallen into the appliance, the appliance has been exposed to rain or moisture, does not 
operate normally or has been dropped. 

 

 

Never

 bypass a fuse. 

 

 

Replace fuses only  with original types having the same ampere value, the same voltage endurance 
and the same time-lag. You can find the corresponding value in chapter 

5.4

 of this instruction manual 

or on the backside of the apparatus. 

 

 

No user-serviceable parts inside. 

 
 
 

3  Unpacking 

 
 
Great  care must  be  exercised  when  unpacking  the  unit.  Carefully  store  the  transportation  packaging  for 
the  possibility of further  use. If  you have a claim on the  warranty,  always use  the original packaging for 
any necessary transportation. Transportation without this packaging can lead to damage to the housing. 
 
Please check, if the following items are included: 
 
1 x AC mains cable (type depends on your country) 
1 x ACCUSTIC ARTS

®

 system remote control 

– SRC II 

2 x batteries for the remote control 
1 x replacement fuse (type depends on your mains voltage) 
 
 
 

4  Positioning 

 
 
The  DRIVE  I 

– MK 2 has  no special requirements regarding its position, but it  should be positioned on 

stable,  even  and  horizontal  surface.  You  can  even  put  the  unit  in  a  cupboard.  For  reasons  of  better 
access  to  the  various  input  and  output  sockets  we  recommend  you  position  the  unit  in  an  audio  rack. 
Professionally  designed  audio  racks  can  have  a  positive  effect  on  the  music  reproduction  of  your  audio 
system. 
 
 

 
CAUTION! 

 
Please observe at all times 
 
Before you connect the DRIVE I 

– MK 2 with some other unit using a cable, 

please  never  forget  that  both  units  must  first  be  switched  off  and 
disconnected from the mains power. 
 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for AMP I MK 2















Reviews: