background image

 

 

not reverse. If it is reversed, the machine will be damaged and it cannot be used 

anymore. 

 

4.  Connect  the  wires  of  the solar  panel,  pay  attention  to  the  positive  and 

negative poles, do not reverse; if there is sunlight, the solar controller inside the 

machine will charge the battery, otherwise check the connection cable is correct. 

 

5. Finally connect the load and then the city power line. 

 

Warning 

Installation  must  be  performed  by  qualified  technicians  with  reference  to 

relevant safety standards

 

 

Environment 

1.

 

The equipment must be installed vertically on a horizontal shelf or on 

the ground. Do not stack objects on the equipment

 

2.

 

The  ambient  temperature  range  for  equipment  operation  is  0°C  to 

40°C,  and  the  ideal  temperature  condition  is  15°C  to  25°C;  the  air 

humidity is 0-95% without condensation; the battery life is defined at 

20°C,  starting  from  20°C  each  Increasing  10°C  will  reduce  the 

expected service life by 50%. 

 

 

 

 

 

 

Space size 

1. Placement of equipment 

Leave  20cm space at the top and  four  sides  of  the  device to keep the 

air pass unimpededly 

Summary of Contents for 500W/18V















Reviews: