background image

 

 

this device. 

 

 

 

 

 

 

 

 

 

Warning 

Our  company  considers  the  personal  safety  of  the  customer  in  the  most 

important  position.  Therefore,  the  customer  or  the  operator  must  read  the 

relevant  steps  in  detail  before  using  the  device  and  strictly  observe  the  usage 

rules  when  using  it.  Even  if  all  the  switches  are  disconnected,  there  is  still  a 

danger of high voltage in the equipment. Any operation that requires the device 

to be moved or opened must be done by an Authorized Technician. 

 

  Transportation and storage

 

 

Transportation 

When  the  goods  are  sent,  they  have  been  thoroughly  inspected.  After 

receiving the goods, please check whether the packaging is damaged or not. 

If there is any damage or missing items, you must notify the dealer within 7 

days after receiving the goods. 

 

Unpacking 

To  avoid  damage  to  the  equipment,  special  care  should  be  taken  when 

moving the equipment; when unpacking the packaging material, ensure that 

it is intact and stored properly for emergency use. 

 

storing 

After the device is received, if it will not be used within seven days, store it 

in a clean, dry, room temperature (0°C to 40°C). 

 

Transportation 

The  equipment  must  be  kept  upright  and  handled  with  care.  Any  fall  or 

Summary of Contents for 500W/18V















Reviews: