ACE Stoßdämpfer GmbH · Postfach 1510 · D-40740 Langenfeld · T +49 (0)2173 - 9226-10 (Technik -20) · F +49 (0)2173 - 9226-19 · info@ace-int.eu · www.ace-ace.com
Stand 03.2021
ACE Stoßdämpfer GmbH · www.ace-ace.com
21_22_0019 Issue 05.2022
3
Mounting instructions and mounting accessories
Construction size:
Ø 15 mm
Max. speed:
50 rpm
Lifetime:
50,000 cycles (1 cycle = 360° left-hand,
360° right-hand), at least 80 % of the original damping torque
after this. The service life may be significantly higher or lower,
depending on the application.
Operating temperature range:
0 °C to +50 °C
Pressure angle:
20°
Material:
Outer body, shaft, gear: Plastic
Mounting:
in any position
Tooth:
Involute gearing
P.C.D.:
7 mm
Number of teeth:
14
Module:
0.5
Damping medium:
Silicone oil
Mounting information:
Attach the damper to the securing tabs
in such a way that the part to be braked cannot exert any side
forces on the damper. Turn the shaft opposite to the damping
direction to avoid damaging the free-wheel mount. No axial or
radial forces may be introduced via the shaft. The rotary axis was
not designed for side loading (see diagrams).
Safety instructions:
Do not use rotary dampers as supports.
Packaging disposal:
Please dispose of the transportation pack-
aging in an environmentally-friendly manner. Recycling packaging
materials saves raw materials and reduces waste. The packaging
materials do not contain any prohibited materials.
Angular offset
Misalignment
Side loading
End loading
Note! The rotary axes, square mounts or free-wheel
mounts are not designed for side loading.
Installation instructions
Before installation and use check whether the identification num-
ber on the product or on the packaging matches the respective
designation on the delivery note.
Rotary dampers are maintenance-free and ready-to-in-
stall.
WARNING
The specified rated damping torque
applies at a temperature of 23 °C or a
speed of 20 rpm.
The damping torque can change depending
on the temperature or speed. Please observe the characteristic
curves in the mounting instructions.
The flap/mass can fall off during installation and removal
of the rotary damper.
Secure moving flap/mass against falling
down!
Depending on the application, failure of the product could
lead to personal injuries and/or material damage.
Use
additional safety elements.
Exceeding the permissible temperature range, the max.
speed, the cycle number and the specified damping torque
can lead to premature failure or destruction of the rotary
damper.
Operating temperature range, speed of 50 rpm, cycle
number of
10/min. and the specified damping torque must be maintained.
Dirt, swarf and aggressive liquids can cause premature
failure of the rotary damper.
Protect or encapsulate rotary
damper from external materials in the surrounding area.
Do not use rotary dampers in high-pressure or vacuum
range.
1.5
1.0
0.5
0
101
600
450
300
200
Ncm
0 3 5 10
20
30
40
50
rpm
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0 10 20 30 40 50
101
600
450
300
200
Ncm
°C
2.6
19 +/- 0.05
2.1
2.1
7
2.5 +/- 0.05
15
3.6 +/- 0.05
Ø
Ø
Ø
8
24
2.2
3.7
2.5
6.6 (5.4)
Ø
Dims. in ( ) without gear
Performance data
TYPES
1
Damping torque
Ncm
Damping direction
Gear
Module
Number of
teeth
Pressure
angle
°
P.C.D.
mm
Weight
kg
FRT-G2-200
0.20 +/- 0.07
two-sided
without
-
-
-
-
0.00060
FRT-G2-300
0.30 +/- 0.08
two-sided
without
-
-
-
-
0.00060
FRT-G2-450
0.45 +/- 0.10
two-sided
without
-
-
-
-
0.00060
FRT-G2-600
0.60 +/- 0.12
two-sided
without
-
-
-
-
0.00060
FRT-G2-101
1.00 +/- 0.20
two-sided
without
-
-
-
-
0.00060
FRT-G2-200-G1
0.20 +/- 0.07
two-sided
with
0.5
14
20
7
0.00080
FRT-G2-300-G1
0.30 +/- 0.08
two-sided
with
0.5
14
20
7
0.00080
FRT-G2-450-G1
0.45 +/- 0.10
two-sided
with
0.5
14
20
7
0.00080
FRT-G2-600-G1
0.60 +/- 0.12
two-sided
with
0.5
14
20
7
0.00080
FRT-G2-101-G1
1.00 +/- 0.20
two-sided
with
0.5
14
20
7
0.00080
1
The indicated damping torques refer to a rotational speed of 20 rpm and an ambient temperature of 23 °C.
Characteristic curves
At 23 °C ambient temperature
FRT-G2
At 20 rpm speed
Provide an external guide or support.
On request:
Special designs available on request. Toothed
plastic racks (modules 0.5 to 1.0) are available for the rotary
dampers with pinions.
Rotary Damper FRT-G2 (continuous rotation)
