background image

 

 
 
 
 
 
 

 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

TABLE OF CONTENTS

 

 

FOR YOUR SAFETY -------------------------------------------------- 1 

SAFETY PRECAUTIONS -------------------------------------- 2 
SPECIAL NOTES ON LCD MONITORS ------------------- 3 

 

BEFORE YOU OPERATE THE MONITOR ---------------------  3 

FEATURES -------------------------------------------------------- 3 
PACKING LIST ---------------------------------------------------  3 
INSTALLATION INSTRUCTIONS ---------------------------  4 
CONTROLS AND CONNECTORS -------------------------- 5 
ADJUSTING THE VIEWING ANGLE -----------------------  6 

 

OPERATING INSTRUCTIONS ------------------------------------- 7 

GENERAL INSTRUCTIONS ----------------------------------  7 
HOW TO ADJUST A SETTING ------------------------------  9 
ADJUSTING THE PICTURE -----------------------------

 

10-11 

PLUG AND PLAY -----------------------------------------------  12 

 

TECHNICAL SUPPORT(FAQ) --------------------------------

 

 

13-14 

ERROR  MESSAGE & POSSIBLE  SOLUTION -------   15 

 

APPENDIX -------------------------------------------------------------  16 

SPECIFICATIONS ------------------------------------------ 16-17 
FACTORY PRESET TIMING TABLE ---------------------   18 
CONNECTOR PIN ASSIGNMENT ------------------------   19 

 

 

 

Summary of Contents for AL1922 r





















Reviews: