26
Chapter 2
Power
The Power screen allows the user to configure CPU and power management options.
The table below describes the parameters in this screen. Settings in
boldface
are the default and suggested
parameter settings.
Parameter
Description
Submenu Items
Advanced CPU
Control
Enter the Advanced CPU Control menu.
•
IST Configuration
•
Thermal Mode
•
CMP Support
•
Use NX capability
•
C-State support
•
Enhanced C-States Enable
•
Pop Up Support
•
Pop Down Support
•
Hard C4E
•
Bi-directional PROCHOT#
•
ACPI 3.0 T-States
•
DTS Enable
•
Thermal Trip Points Setting
(Throttle On Temp.)
Platform Power
Management
Enter the Platform Power Management
menu.
•
PCI Clock Run
•
_CST - C4 Latency Value
ACPI S3
Enable
or Disable ACPI S1/S3 Sleep State.
N/A
Wake on PME
Disable
or Enable wake up when the
system power is off and a PCI Power
Management Enable wake up event occurs.
N/A
Wake on Modem
Ring
Disable
or Enable wake up when the
system power is off and a modem attached
to the serial port is ringing.
N/A
I t e m S p e c i f i c H e l p
T h e s e i t e m s c o n t r o l
v a r i o u s C P U p a r a m e t e r s .
F 1
E S C
H e l p
E x i t
S e l e c t I t e m
S e l e c t M e n u
C h a n g e Va l u e s
S e l e c t
S u b M e n u
E n t e r
F 9
F 10
S e t u p D e f a u l t
S a v e a n d E x i t
[ E n a b l e d ]
[ D i s a b l e d ]
[ D i s a b l e d ]
[ D i s a b l e d ]
[ D i s a b l e d ]
[ E n a b l e d ]
[ D i s a b l e d ]
[ D i s a b l e d ]
[ D i s a b l e d ]
[ D i s a b l e d ]
X
A d v a n c e d C P U C o n t r o l
X
P l a t f o r m P o w e r M a n a g e m e n t
A C P I S 3 :
W a k e o n P M E
W a k e o n M o d e m R i n g
A u t o w a k e o n S 5
Q u i c k l y S 4 R e s u m e
X
A d v a n c e d C P U C o n t r o l
X
P l a t f o r m P o w e r M a n a g e m e n t
A C P I S 3 :
W a k e o n P M E
W a k e o n M o d e m R i n g
A u t o w a k e o n S 5
Q u i c k l y S 4 R e s u m e
F 5 / F 6
I n s y d e H 2 0 S e t u p U t i l i t y R e v . 3 . 5
Boot
Exit
Security
Information
Advanced
Power
Main
Summary of Contents for Aspire One AOD150
