background image

6

4.0  Use of the Instrument

4.1 Preparation and Safety Measures
Before connecting the test leads always set the measurement
range switch to the desired function.
Before switching to a new function or to a different measurement
range disconnect the leads from the test object.
The instrument may only be used in dry and clean environments.
Dirt and humidity reduce the insulation resistance and can lead to
electric blows when working with high voltages particularly.
The instrument may only be used within the operating ranges as
specified in the technical data section.
Prior to usage check the instrument for perfect functioning on a
known voltage source (see also DIN VDE 0105, Part 1).

PASAR 323 has an Auto Range function that will automaticly
search for the best measurement range.

4.2  Voltage Measurement AC/DC
Do not connect the probes to more than 600V AC/DC. Exceeding
these values can endanger the operator, and may result in damage
to the instrument.
1)

Select measurement range (V- / V~) via measurement

functionselection switch (4).

2)

Connect the black test lead to the COM socket and the red test

lead to the ”V 

Ω 

mA

 

” socket.

3)

Connect test leads to UUT.

4)

The value measured is shown on the digital display.

4.3 Current Measurement 10A/15A AC/DC
Do not carry out current measurements in systems with more than
250V.
1)

Select measurement range ”AAC” or ”ADC” via measurement

function selection switch (4).

2)

Connect the black test lead to the COM socket and the red test

lead to the ”15A” socket

3)

Connect multimeter in series to the test object and then switch

on UUT.

Summary of Contents for PASAR 323













Reviews: