background image

深圳利洋焊接设备

Shenzhen LiYang welding Equipment Co., Ltd

LY

as possible .Avoid it closing to air conditioners, fans and the other outlet.

2

IR6000 

Rework Station sensor Direct contact with motherboard

So Temperature

display is Actual temperature

3

In order to avoid damage to the motherboard capacitor

SO use insulation tape please 

Maintenance completed ,then Removal of insulation tape 

So as to avoid short-circuit

4

After removal of BGA chip 

PCB Bonding Pad Need to clean up 

Avoid cold solder joint

See BGA chip tin completely liquefied, Then To move the BGA chip

So as to avoid Bonding

Pad Damage 

5

BGA chips should be subject to settlement, floating state 

Prohibited in all solder ball

did not fully liquefied, by force if removal of chips, so as to avoid pad off, chip or
motherboard scrap!

6

To improve success rate of Rework , PCB and chips need drying and processing in principle

PCB board or chip moist heat process will occur in the burst phenomenon, the Rework

process may hear the blasting sound of a minor

According to actual situation Please

self-control.

7

PCB board heating time is too long or repeated several times the surface heating will lead to

discoloration.

8

Users from modifying temperature parameters

Please use scrap PCB tested

Heating whole

time about 10 seconds before the end of solder balls should be fully liquefied

f the

liquefaction advanced or delayed,

,!

Should be regulating up/down the temperature setting.

So as to avoid heat damage to chips or low-temperature sealing-off

9

The  factory equipped  with  two  sets  of  programmable  temperature  control  table  used

parameters:

The attached curve setting for reference

WWW.LYBGA.COM

16

Summary of Contents for IR6000


















Reviews:

Related manuals for IR6000