background image

3

1. Advisement

 

WARNING

Always have the unit installed by the store it was purchased from.

 

Improper connections and/or installation could result in electrical shack,

fire or other serious injury or damage.

Do not place the unit on an unstable surface.

 

Always checks the strength and stability of the installation location.

 

A falling unit will result in damage and could cause serious injury

Never disassemble or attempt to repair or modify the unit.

 

Disassembly by untrained personnel could result in serious electrical

shock, fire and/or malfunction.

Never use in locations where combustible materials are used.

 

The unit should never be used where combustible materials, such as

gases, are being used.

 

Fire, explosion or other serious accidents could occur.

Never touch electrical connections with wet hands.

 

Touching electrical connections with wet hands could result in serious

electrical shock.

Never expose the unit to water.

 

If the unit becomes wet, turn off the power and unplug it immediately.

 

Stop using the unit if it becomes wet and contact your nearest dealer.

Never use the unit if there is an abnormality.

 

Turn off the power and unplug the unit immediately if there is any type of

abnormality, such as a strange smell or smoke.

 

Continuing to use a unit that is not operation properly could result in

serious injury or damage ta the unit.

Always use the designated power supply.

 

Failure to use the proper power supply could result in fire, electrical shock,

serious injury and/or damage.

 

Always uses the designated power supply.

Always handle the connecting cords properly.

 

Never damage or modify the connecting cords.

 

Never pull on the connecting cord, expose them to extreme heat and/or

place heavy objects on top of them.

 

Failure to follow these warnings could result in fire, electrical shock or

other damage or injury.

 

CAUTION

Always use the unit indoors.

 

The unit should never be used outdoors, or in any place where it will be

exposed to rain or other extremes of moisture.

 

Direct exposure to water will result in rust and will damage the unit.

Never use in environments that have heavy concentrations of dust,
smoke, steam or humidity.

 

Environments such as these could result in fire, electrical shock or other

serious damage or injury.

Never place the unit in extremes of high or low temperatures.

 

Extreme temperatures will damage the unit.

 

Always use within an operating range of 0 °C to 40 °C.

Never mount in areas exposed to direct sunlight.

 

Direct sunlight can also discolor the unit and cause other damage.

Never expose the unit to impact.

 

Strong impact may seriously damage the unit.

 

FOR PROPER OPERATION

Never install the unit yourself.

 

The unit should be installed by trained personnel.

This product has been designed and manufactured in accordance with the
harmonized European standards, following the provisions of the below stated
directives.

Electromagnetic Compatibility Directive 89/336/EEC

 (EN 61000-3-2:1995,

EN 61000-3-3:1995, EN 50081-1:1992, EN 50082-1:1997).

This devise complies with part 15 of the FCC rules operation is subject to the
following two conditions: (1) This device may not cause harmful  interterence
and (2) This device must accept any interference received including
interference that may cause undesired operation.

Summary of Contents for AT6SD














Reviews: