background image

2

 

!

 

WARNING

The ADARAC™ Truck Bed Rack, ADARAC™ Aluminum M-Series, ADARAC™ 

Aluminum Series, ADARAC™ Aluminum Pro Series and ADARAC

TM

 Aluminum Upright 

Kits have a load capacity of 250 lbs. per cross bar and a maximum load capacity of 

500 lbs., evenly distributed among cross bars. Always secure cargo properly. Failure to 

secure cargo or hauling inappropriate cargo may result in personal injury or death. Agri-

Cover, Inc. is not responsible for any property damage, personal injury or death incurred 

while using any Agri-Cover, Inc. product.

 

!

 

CAUTION

These products are only intended for transporting cargo evenly distributed on cross bars. 

It is the responsibility of the user to secure these materials to the rack before transporting. 

Never load your rack to exceed the safe capacity of your vehicle. 

Heavy loads when carried high can dangerously alter the center of gravity of your 

vehicle. Consult your vehicle’s owner’s manual for specifications on load ratings and 

recommendations of installation of aftermarket racks. Any modifications made to this 

product or use of this product for any other purpose than its intended use could create a 

hazardous condition that can cause serious personal injury or property damage.

NOTE

Before entering low clearance areas, check height clearance to ensure safe entry 

(empty or loaded).

 

NOTICE

Any modification or unintended use of these products shall immediately void all 

manufacturer's warranties. Manufacturer disclaims all liability for injuries to persons or 

property resulting from any modification to or unintended use of these products.

Some vehicle manufacturers require a reinforcing kit, available through the vehicle 

dealership, to be installed on the truck box prior to mounting any kind of rack. Contact 

your dealership to see if your vehicle requires a reinforcing kit before installation.

NOTE: 

Installation and use of any box rail mounted accessory may cause minor 

aesthetic damage to exterior of vehicle. Agri-Cover, Inc. makes no claims or warranties 

as to a particular vehicles ability to support rail mounted accessories without incurring 

damage. See your vehicle manufacturer’s specifications for bed rail mounted 

accessories.

Summary of Contents for ADARAC Aluminum M Series

















Reviews: