background image

Page 6

Automation Components, Inc.

2305 Pleasant View Road  |  Middleton, WI 53562

Phone:

 1-888-967-5224  |  

Website:

 workaci.com

Page 7

WARRANTY

The ACI PM Room Series are covered by ACI’s Two (2) Year Limited Warranty, which is located in the front of ACI’S 
SENSORS & TRANSMITTERS CATALOG or can be found on ACI’s web site: www.workaci.com.

W.E.E.E. DIRECTIVE 

At the end of their useful life the packaging and product should be disposed of via a suitable recycling 
centre. Do not dispose of with household waste. Do not burn.

PRODUCT SPECIFICATIONS

16-28VAC/16-35VDC (Reverse Polarity Protection)
4-20 mA: 500 Ohms maximum | 0-10 VDC: 2K Ohms Minimum
0~500μ g/m3
4-20mA(Default), 0-10VDC
N.O. rated 3A @ 30VDC, 3A @250VAC
100μ g/m3
+/-10μg/m3 @ 0~100μg/m3, +/-10% reading @ 
100~500/600µg/m3@25°C/50%RH
1 μg/m3
In continuous service mode, sample time <1s, response time <10s
15 minutes
MTBF more than 3 years in continuous service mode, service life up to 8-10 
years in auto (intermittent)
service mode
Modbus RTU; EIA RS-485
1-247
4800 or 9600
None/Even/Odd
1
8
Screw Terminal Blocks / 16 AWG (1.31 mm2) to 22 AWG (0.33 mm2)
0.45 lbf-in (0.5 Nm) nominal
32 to 122°F (0 to 50°C)
-30 to 70°F (-34 to 21°C)
10 to 95% RH, non-condensing
IP30
ABS Plastic / UL94V-0

Supply Voltage:
Output Load Resistance:
Measurement Range:
Output:
Relay:
Relay Trip Point:
Accuracy: 

Resolution:
Response Time:
Warm Up Time:
Service Life: 

Communication Protocol:
Sensor Addresses:
Supported Baud Rates:
Parity:
Stop Bits:
Databits:
Connections / Wire Size:
Terminal Block Torque Rating:
Operating Temperature Range:
Storage Temperature Range:
Operating Humidity Range:
Enclosure Protection:
Enclosure Material / UL Flammability:

Version: 1.0

I0000941

Summary of Contents for PM2.5-ROOM









Reviews: