aci SNOWSPORT HD Utility Plow Installation Instructions Manual Download | Manualshive

Page: 11 / 16

background image

10

11

2: ASSEMBLING SNOWPLOW

(Continued)

M. Center rubber cutting edge with lower aluminum blade.
N. Drill 5/16” pilot hole at factory mark in groove on each end of blade, drill only through

first layer of aluminum and into rubber.

O. Turn

3/8" x 1" self-threading flange bolt

s into 5/16" pilot holes and tighten.

3/8" x 1" Self-threading

flange bolt

P. Hang one end of blade assembly into retainer groove on push frame. Repeat for

opposite end of blade assembly.
Q. Insert quick pin in hole, rotate pin just enough to allow through second hole and then

rotate back to its secure position. Repeat for remaining quick pin.

Quick pin

«
...
9
10
11
12
13
...
»

Summary of Contents for SNOWSPORT HD Utility Plow

















Reviews:

No comments

Related manuals for SNOWSPORT HD Utility Plow

Brand: Nakayama Pages: 13

Brand: Yardworks Pages: 18

Brand: Land Pride Pages: 48

Brand: Tarmo Pages: 36

Brand: Champion Pages: 2

Brand: Herz Pages: 7

Brand: Hitachi Pages: 16

Storm Tracker 1028

Brand: Troy-Bilt Pages: 32

Brand: Troy-Bilt Pages: 52

Storm Tracker 2690

Brand: Troy-Bilt Pages: 52

Brand: Stanley Pages: 19

Brand: MTD Pages: 28

Bolens Premium 31AH5WL3

Brand: MTD Pages: 48

Brand: Cub Cadet Pages: 16

Brand: Troy-Bilt Pages: 48

Brand: Stihl Pages: 24

Brand: Stihl Pages: 360

Brand: Mask Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands