background image

13 

The battery when shipped alone is a class 9 hazmat, under the category of lithium batteries 
UN 3090. If the total weight of the shipment exceeds 5 kg they are restricted from carriage 
in passenger carrying aircraft. 

 

THE FOLLOWING IS AN EXCERPT FROM FAA AC 91-44A PARAGRAPH 8.a WHICH 

DEFINES WHEN ELT BATTERY REPLACEMENT MAY BE DONE UNDER 14 CFR PART  

43.3(h) AS PREVENTIVE MAINTENANCE. 

 

“…The replacement can be done by the pilot if the preventive maintenance limitations of part 43.3(h) of 
the FAR, are complied with. For example, a portable type ELT that is readily accessible and can be 
removed and reinstalled in the aircraft by a simple operation should be considered preventive 
maintenance. Fixed type ELT installations are often permanently mounted in a remote area of the 
aircraft near flight control cables, vital aircraft components, and critical attachments to the aircraft 
structure. Installations of this nature require an external antenna and often a remote on/off transmitter 
control switch that is usually located near the pilots flight position. This type of installation is complex 
and battery replacement should be accomplished by a certified mechanic or certified repair station…” 

SECTION 13 WARRANTY PROCEDURE 

 

Should it become necessary to return the ELT for warranty service. 

REMOVE THE ELT 

BATTERY BEFORE SHIPPING THE UNIT TO OUR FACILITY

. The battery is 

DOT/IATA 

CLASS 9 HAZARDOUS MATERIAL, 

and DOT/IATA regulations must be followed whenever 

shipping the battery, or ELT and battery. See section 11 page 12 for additional shipping 
information. 

 

All units must be returned to our facility freight prepaid. Our shipping  
Address is as follows: 

 

ACK TECHNOLOGIES, INC. 
440 W. JULIAN ST. 

SAN JOSE, CA  95110      

Provide an address  that UPS  will deliver to 

SECTION 12 PROGRAMMING 

 

THE ELT IS FACTORY PROGRAMMED TO THE STANDARD LOCATION SERIAL NUMBER 

FORMAT WITH U.S.A. COUNTRY CODE. (366) 

 

The ELT may be programmed in the field to the following formats: 

 

Serial number (you may only reprogram the country code in this format.) 

 

Standard location 24-bit address 

 

Standard location with operator designator & serial number 

 

To reprogram the ELT you must use our programming dongle.  
(P/N E-04.prg Ver 2.1) the module interfaces to a PC operating Windows XP, Windows 7 
Professional via a USB port.  

 

The programming software and manual may be downloaded from our web site.  

WWW.ACKAVIONICS.COM

 

DO NOT REMOVE SEALANT FROM BATTERY PACK SCREWS, OR DISASSEMBLE 
BATTERY PACK .TSO-C142a PROHIBITS OPENING OR REPLACING CELLS. IF THE 
BATTERY PACK IS OPENED  BY ANYONE EXCEPT THE MANUFACTURER IT IS  NO 
LONGER AIRWORTHY, AND THE WARRANTY IS VOID. 

Summary of Contents for E-04





















Reviews: