background image

Page. 8

STEP 1

STEP 2

STEP 3

STEP 4

a. 

Press the UP bu  on. 

The curtain should open.

 

Press the DOWN bu  on. 

The curtain should close.

To reverse direc  on; 
b. 

Repeat Step 1a - 1b

c. 

Press the DOWN bu  on. 

 

The LED light will 

fl

 ash 

fi

 ve 

Ɵ

 mes.

a. 

Press the UP bu  on. 

 

The curtain will hit the edge of the track.

b. 

Press the DOWN bu  on. 

 

The curtain will close completely.

a. 

Direct the Curtain to your desired Favourite posi  on 

 

using UP/DOWN and STOP bu  ons.

b. 

Press P2 once. 

The LED light will 

fl

 ash once.

c. 

Press STOP 5   mes. 

 

The LED light will 

fl

 ash every 

Ɵ

 me STOP is pressed (

fi

 ve 

Ɵ

 mes).

CHECK DIRECTION

AUTOMATIC LIMIT SETTING

SET FAVOURITE  INTERMEDIATE  POSITION

PAIR MOTOR WITH REMOTE

a. 

Press the Se   ng Bu  on on the motor for approx. 2 secs.

 

When the LED light 

fl

 ashes, release Se

ƫ

  ng Bu

Ʃ

 on.

b. 

Press P2 bu  on on the remote twice. 

 

The 

LED light will 

fl

 ash every 

Ɵ

 me P2 bu

Ʃ

 on is pressed.

c. 

Press UP once; the LED will 

fl

 ash 

fi

 ve   me.

se   ng bu  on

external swith 
interface

LED light

A U T O M A T E   C - C U R T A I N   M O T O R   P R O G R A M M I N G

Summary of Contents for Automate RF 500 Series









Reviews: