background image

www.ACOPower.com

Power Your Green Life!

KIT-HYS200MB

 

4120 Valley Blvd Walnut, CA 91789, USA

+1-626-737 1140

Introduction

 Features

User’s guide

This portable solar panel comes with a pre-installed charge controller. This charge controller protects battery against 

unsafe electrical conditions and must be used to charge 12V batteries. To charge solar generators with a built-in charge 

controller, simply use the MC4 cables provided and plug them into the cables that came with your power station to 

charge. A 12V battery and solar generator can be charged at the same time.

• Max 200 watts solar panel 

• 20A PWM charge controller

• Portable

• Removable MC4 Connectors

• Charge 12V battery by alligator clamps- Sealed, Flooded, GEL, AGM, Lithium and other deep cycle batteries

• Charge 12V solar generator by MC4 adapter- battery with inverter, power bank/station with built-in charge controller.  

   ACOPOWER solar generator 150wh and 220wh recommended

• Can be used on its own or as part of a larger solar system

• Extendable with MC4 Connectors

After receiving the solar panel kit, please check if all accessories are included in the package and prepare to test your kit: 

1. Locate a sunlit area clear from hanging branches or obstacles.

2. Unclip the two latches (2, Table 1) on the side of the unit and fold two panels outward. Extend the two support legs (4, 

Table 1) to desired length and lock the stands in position. Set solar panel kit in the position facing the sun.

Tip: 

To obtain the maximum output power of solar modules, it is recommended to adjust the solar modules based on solar 

trajectory.

How to test the solar panel

Method 1: Use a multimeter

Set your multi-meter to measure DC voltage and put the red probe on the red positive MC4 cable (14a, Table 1) and the 

black probe on the black MC4 cable (14b, Table 1) and make sure the connections are secure. the open-circuit voltage 

should be displayed on your multi-meter and it should be around 17.6V-23V. This is your solar panel’s voltage without 

going through the charge controller. 

If you’re not getting something within that range or close to those numbers, you should check and make sure the solar 

panel is in direct sunlight and that the connections between the MC4 cables and the multi-meter is secure. 

Summary of Contents for KIT-HYS200MB













Reviews: