background image

COPYRIGHT 2010 - 2020, ACCELERATED CARE PLUS CORP., ALL RIGHTS RESERVED

 

 

NOTE:

 

NOTE:

 

NOTE:

 

Example:

 

28 

OMNICYCLE

® 

ELITE USER MANUAL

 

 

 

Spastic Automation:  

A “Neuro” function. The Spastic Automation function is used to set the direction of rotation 

following detection of a spasm. Select from the following options:

 

 

Forward 

if the patient tends to suffer extension spasms

 

 

Backward 

if the patient tends to suffer flexion spasms

 

 

Change 

to have the exerciser rotate in the opposite direction to the direction it was rotating when the spasm 

was detected

 

 

Follow 

to have the exerciser rotate in the same direction it was rotating when the spasm was detected

 

 

Speed  Adaptation:   

A  “Neuro”  function.  If  Automatic  Speed  Adaption  is  set  to  “ON”  the  “assisted”  exercising 

(motor) speed automatically adjusts to greater effort by the patient when exercising “actively.”

 

 

If a patient is exercising in  “active”  mode” at 50 rpm  when  the  motor speed (“assisted” exercising 

speed)  is  set  to  20  rpm,  after  every  10  seconds,  the  Omnicycle

® 

Elite  adjusts  the  “assisted”  exercising  speed 

upward by  1 rpm to  a  maximum of  35 rpm.  If  the  patient subsequently  changes back  to  “assisted” exercising, 
the Omnicycle

® 

Elite drops the speed to 5 rpm lower than the active speed, or 30 rpm, whichever is lower. Thus 

the  patient  individually  controls  the  speed  and  obtains  an  “assisted”  exercising  speed  at  which  he/she  is 
comfortable.

 

 

Heart rate limit: 

The Omnicycle

® 

Elite reduces the resistance level as soon as the pre-set heart rate limit is reached. 

This is to ensure that the patient always exercises at a heart rate below the pre-set limit.

 

Because a high level of effort is required for all Ortho and Cardio exercising programs, using a long 

crank length is advisable.

 

 

Level: 

This  function  applies  to  the  biofeedback-based  exercise  programs  Soccer,  Porcupine  and  Traffic  Jam.  This 

function allows the operator to choose a difficulty setting of minimal, moderate or maximum.

 

 

Maximum  Symmetry: 

Available  for  lower  extremity  Porcupine  program.  Allows  the  operator  to  adjust  how  close 

the  Porcupine  will  be  positioned  from  the  edge  of  the  border  by  percentage  (70%  80%  90%  100%).At  100%  the 
Porcupine will be at edge position of the border.

 

 

Muscle  Support: 

An  “Ortho”  function.  This  function  assists  patients  with  only  minimal  residual  strength  or 

minimal strength on one side. The residual strength is supplemented by this function so that an even pedaling action 
is always obtained. The function operates according to the principle of “as much assistance as necessary but as little 
assistance as possible.”  The objective of  this  function  is to optimize  the  patient’s exercise  effort at  all  times  and  to 
achieve greater symmetry.

 

 

In the case of leg-amputee patients, the Muscle Assistance function performs the work of the inactive 

side. In such cases, the Muscle Assistance function operates like an “electronic flywheel”.

 

 

Sens. Mic: 

(Microphone sensitivity) A System function.  The Omnicycle

® 

Elite can be stopped by a long, loud shout 

(safety  voice  deactivation).  This  function  is  particularly  useful  for  patients  who  use  the  upper  extremity  exerciser 
with  their  arms  strapped  to  the  armrests  and  cannot,  therefore,  use  the  control  pad.  The  safety  voice  deactivation 
function is always active. The menu option Technical/Microphone sensitivity allows you to set the sensitivity of the 
integrated microphone in the control pad. Set the sensitivity as follows:

 

 

1 to 3 if the ambient noise is very loud

 

 

4 to 6 if the ambient noise is of a normal level

 

 

7 to 10 if the ambient noise is very quiet

 

 

OFF if the therapist wishes to deactivate the microphone

 

 

Check  that  the  setting  is  correct  by  carrying  out  a  practical  test.   Afterwards  press  the  “START” 

button to continue the exercising session.

 

 

Contrast:  

The contrast of  the  color  screen  is  set  at  the  factory.   If  necessary,  it  can be  adjusted  by  selecting  the 

menu option “Technical/Contrast.”

 

Summary of Contents for OMNICYCLE ELITE

















































Reviews: