background image

OMNISWD

®

 USER MANUAL 

 

31 

COPYRIGHT © 2019-2020, ACCELERATED CARE PLUS CORP., ALL RIGHTS RESERVED 

STANDARD LIMITED PRODUCT WARRANTY 

The warranty information provided in this section is applicable only to products purchased from ACP, 
directly or through an authorized dealer.  This section does not  apply to leased products.  The terms of 
maintenance and repair of any leased products are detailed in the separately executed agreement between 
the parties. 

Warranty Coverage 

This warranty provides coverage, for Equipment purchased, against manufacturer’s defects in material and workmanship, 
and extends to the original owner of the product during the warranty period for that product.  Only those items returned to 
the ACP Service Center within the warranty period, and also within thirty (30) days after notification to ACP of the defect, 
shall be eligible for repair under the Standard Limited Product Warranty.  Buyer is responsible for shipping cost associated 
with sending the Equipment to the ACP Service Center.  ACP shall ship Equipment to Buyer after repair at no cost to the 
Buyer provided repair is deemed to be under warranty.   ACP may, at its discretion and only for valid warranty claim, repair 
or replace any part(s) that prove to be defective during the warranty period. 
 

Warranty Exclusion 

 

Any and all warranty coverage will be void if any of the following have occurred: 

 

1. 

The product contains repairs or replacement parts not furnished by ACP. 

2. 

The product is damaged resulting from misuse or negligence. 

3. 

The product has been tampered with and/or altered, including serial number alteration. 

 

Note:

  Use of the Equipment with accessories and/or supplies not approved by ACPL for use with the Equipment may 

void the warranty if such accessory or supply item caused damage to the Equipment.

 

 

Warranty Period 

 

The following coverage is provided at no additional cost to the Buyer: 

 

New Equipment / Product

.  Products purchased as new from ACP are warranted against manufacturer’s defects in 

material and workmanship for a period of two (2) years from the date of purchase. 
 

Refurbished Equipment / Product.

  Products purchased specifically as Refurbished Equipment are warranted against 

manufacturer’s defects in material and workmanship for a period of one (1) year from the date of purchase. 
 

Accessories.

  All accessories for ACP equipment / products are warranted against manufacturer’s defects in material 

and workmanship for a period of three (3) months from the date of purchase.  

 

Warranty Validation 

 

The following information needs to be provided to the ACP Customer Support representative prior to the product 
being returned under warranty coverage: 
 

1.

 

Buyer name or account number as it appears under the “Bill TO” on the ACP or recognized ACP Dealer invoice. 

2.

 

Invoice Date and Number. 

3.

 

Model number, description, and serial number of equipment. 

4.

 

Detailed description of the problem. 

Summary of Contents for OmniSWD



































Reviews: