background image

Page 2 

AB-8kW-I03-191213 

CONTENTS

 

 

General Safety Notes 

Page 2 

 

Operating Instructions 

Page 9 

Installation instructions 

Page 3 

 

Wood Burning 

Page 11 

Chimney & Flue 

Page 3 

 

Solid Fuel Burning 

Page 13 

Flue Draught 

Page 5 

 

Technical Information 

Page 14 

Flue Stabiliser 

Page 6 

 

Maintenance 

Page 15 

Dimensions & Clearances 

Page 6 

 

Guarantee 

Page 16 

Installing the Stove 

Page 7 

 

 

 

 

GENERAL SAFETY NOTES

 

 

 

 

SE Stoves need to maintain a higher flue temperature than a Non-SE Stove.  As such 
it will not shut down like a Non-SE Stove and is designed to continue to draw air in 
to maintain these temperatures and meet local authority regulations.  

 

Properly installed, operated and maintained, this appliance will not emit fumes into the 
dwelling. However occasional fumes from de-ashing and re-fuelling may occur. 
Persistent fume emission is potentially dangerous and must not be tolerated.  If 
fume emission does persist, open doors and windows to ventilate the room. Let the 
fire burn out or eject and safely dispose of fuel from the appliance. Once the fire is 
cold, check the flue and chimney for blockages and clean if required. Do not attempt 
to relight the fire until the cause of the fume emission has been identified and 
corrected. Seek expert advice if necessary. 

 

Do not fit an extractor fan in the same room as the appliance. 

 

It is important that flue ways are cleaned frequently and the chimney swept regularly. 
Also the stove must be maintained in good mechanical order. Regular sweeping means 
at least once a year for smokeless fuel and a minimum of twice a year for other fuels. 

 

If the chimney was previously used for an open fire, it is possible that the higher flue gas 
temperatures generated by the stove may loosen deposits that were firmly adhering to 
the inner surface of the chimney and cause blockage of the fluepipe. We recommend 
that in such a situation a second sweeping of the chimney should be carried out within 
one month of regular use of the stove after installation. Also, lock or remove any 
existing dampers in the flueway. 

 

Should it be likely that children, aged or infirm people approach the fire, then a 
fireguard should be fitted. 

 

Avoid the use of aerosol sprays in the vicinity of the stove when it is in operation. 

 

This appliance must be installed as per these instructions and regulations complied 
with. No modifications or alterations of any kind are permitted. 

Summary of Contents for BLOOMSBURY SE 8kW

















Reviews: